The automatic transmission fluid temperature (TFT) sensor is a negative coefficient thermistor whose resistance value changes based on temperature. The PCM provides a 5 volt reference to the sensor. A low fluid temperature, an open TFT sensor or sensor circuit results in high signal voltage. The TFT operating range is -40 to +151°C (-40 to +304°F).
If the PCM detects a continuous open or a short to power on the TFT sensor circuit, then DTC P0713 sets. DTC P0713 is a type C DTC.
• | The system voltage is 9-18 volts. |
• | The ignition is ON. |
The PCM detects a TFT sensor voltage greater than 4.92 volts for 6 minutes and 40 seconds continuous.
• | The PCM does not turn on the malfunction indicator lamp (MIL). |
• | The PCM freezes transmission adaptive functions. |
• | The PCM calculates a default TFT from the ECT sensor and the IAT sensor. |
• | The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Failure Records. |
• | The PCM stores DTC P0713 in PCM history. |
• | A scan tool can clear the DTC. |
• | The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without a non-emission related diagnostic fault occurring. |
• | The PCM cancels the DTC default actions when the fault no longer exists and the DTC passes. |
The numbers below refer to the step numbers on the diagnostic table.
A value of 4.9-5.0 volts indicates the PCM and engine side of the wiring are good.
A short to voltage greater than 5 volts would cause the TFT sensor to open.
A short to the TFT sensor signal circuit and any other circuits in the transmission harness could cause the TFT sensor to open.
Step | Action | Value(s) | Yes | No | ||||
---|---|---|---|---|---|---|---|---|
1 | Did you perform the Diagnostic System Check? | -- | Go to Step 2 | Go to Diagnostic System Check - Engine Controls in Engine Controls - 3.8L | ||||
2 |
Important: Before clearing the DTCs, use the scan tool in order to record the Failure Records for reference. Using the Clear Info function will erase the stored Failure Records from the PCM. Does the scan tool display a TFT Sensor voltage less than the specified value? | 4.9 V | Go to Intermittent Conditions in Engine Controls - 3.8L | Go to Step 3 | ||||
Refer to Automatic Transmission Inline 20-Way Connector End View . Does the voltage measure within the specified range? | 4.9-5.0 V | Go to Step 7 | Go to Step 4 | |||||
4 | Does the voltage in Step 3 measure more than the specified value? | 5.0 V | Go to Step 6 | Go to Step 5 | ||||
5 |
Refer to Testing for Continuity and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 13 | ||||
Test the signal circuit (CKT 1227) of the TFT sensor for a short to voltage between the PCM and the AT inline 20-way connector. Refer to Testing for a Short to Voltage and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 11 | Go to Step 13 | |||||
7 |
Refer to Automatic Transmission Inline 20-Way Connector End View . Is the resistance less than the specified value? | 100 K ohms | Go to Step 9 | Go to Step 8 | ||||
8 |
Refer to Testing for Continuity in Wiring Systems. Did you find the condition? | -- | Go to Step 10 | Go to Step 12 | ||||
Measure the resistance between terminal L and all other terminals, except M, of the J 44152 . Is the resistance between terminal L and all other terminals, except M, greater than the specified value? | 1,000 ohms | Go to Intermittent Conditions in Engine Controls - 3.8L | Go to Step 10 | |||||
10 | Replace the automatic transmission wiring harness assembly. Refer to Wiring Harness Replacement . Did you complete the replacement? | -- | Go to Step 11 | -- | ||||
11 | Was the engine harness repaired, or the transmission harness replaced due to a short to power or other circuit? | -- | Go to Step 12 | Go to Step 14 | ||||
12 | Replace the automatic transmission fluid temperature sensor. Refer to Fluid Temperature Sensor Replacement . Did you complete the replacement? | -- | Go to Step 14 | -- | ||||
13 | Replace the PCM. Refer to Powertrain Control Module Replacement in Engine Controls - 3.8L. Did you complete the replacement? | -- | Go to Step 14 | -- | ||||
14 | Perform the following procedure in order to verify the repair:
Has the test run and passed? | -- | Go to Step 15 | Go to Step 2 | ||||
15 | With the scan tool, observe the stored information, capture info and DTC info. Does the scan tool display any DTCs that you have not diagnosed? | Go to Diagnostic Trouble Code (DTC) List in Engine Controls - 3.8L | System OK |