Circuit Description
The instrument panel integration module (IPM) communicates with the HVAC control module through the HVAC control module assembly data signal and HVAC control module clock signal. This communication link is only used by the IPM and the HVAC control module.
Conditions for Running the DTC
The ignition is turned ON.
Conditions for Setting the DTC
| • | There is a loss of communications between the IPM and the HVAC control module. |
| • | The above conditions are present for 3 seconds. |
Action Taken When the DTC Sets
The HVAC system will be disabled.
Conditions for Clearing the DTC
| • | The DTC will become history if the IPM no longer detects a failure. |
| • | The history DTC will clear after 50 fault-free ignition cycles. |
| • | Use the scan tool in order to clear the DTCs. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: HVAC Schematics Connector End View Reference: HVAC Connector End Views | ||||
1 | Did you perform the HVAC Diagnostic System Check? | -- | Go to Step 2 | |
2 |
Are all of the visual indicators illuminated and is the audible indicator ON? | -- | Go to Step 7 | Go to Step 3 |
3 | Observe the display of the HVAC control module. Is the display of the HVAC control module blank? | -- | Go to Step 5 | Go to Step 4 |
Observe the display of the HVAC control module. Does the HVAC control module display only °C °F? | -- | Go to Step 8 | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | |
5 |
Does the test lamp illuminate? | -- | Go to Step 6 | Go to Step 10 |
6 | Connect a test lamp between the ignition 3 voltage circuit and the ground circuit, of connector pin location A1, of the HVAC control module. Does the test lamp illuminate? | -- | Go to Step 15 | Go to Step 11 |
7 |
Does the voltage measure near the specified value? | 1 V | Go to Step 15 | Go to Step 12 |
8 |
Does the voltage measure near the specified value? | 1 V | Go to Step 9 | Go to Step 13 |
9 | Measure the frequency between the HVAC control module clock signal circuit of the HVAC control module and a good ground. Does the frequency measure near the specified value? | 930 Hz | Go to Step 15 | Go to Step 14 |
10 | Repair the ignition 3 voltage circuit of the HVAC control module for a short to ground, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 19 | -- |
11 | Repair the ground circuit, of connector pin location A1, of the HVAC control module for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 19 | -- |
12 | Test the HVAC control module data signal circuit for a short to voltage or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 19 | Go to Step 16 |
13 | Test the HVAC control module data signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 19 | Go to Step 14 |
14 | Test the HVAC control module clock signal circuit for a short to voltage, a short to ground, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 19 | Go to Step 16 |
15 | Inspect for poor connections at the harness connector of the HVAC control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 19 | Go to Step 17 |
16 | Inspect for poor connections at the harness connector of the instrument panel integration module (IPM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 19 | Go to Step 18 |
17 | Replace the HVAC control module. Refer to HVAC Control Module Replacement . Did you complete the replacement? | -- | Go to Step 19 | -- |
18 |
Important: : Perform the Recalibration procedure for the instrument panel integration module. Replace the instrument panel integration module. Refer to Instrument Panel Module Replacement in Body Control System. Did you complete the replacement? | -- | Go to Step 19 | -- |
19 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
