8 Digit GM Part Number: The scan tool displays the eight digit
part number of the driver door module (DDM).
Battery Voltage: The scan tool displays 9.0-15.0 volts.
This is the state of charge of the vehicles battery.
Calibration ID: The scan tool displays the calibration or program
revision level used in the PROM of the driver door module (DDM).
Component Serial # 8-11: The scan tool displays digits
8 through 11 of the driver door module (DDM) serial number.
Component Serial # 12: The scan tool displays digit 12 of the
driver door module (DDM) serial number.
Component Serial # 13-16: The scan tool displays digits
13 through 16 of the driver door module (DDM) serial number.
Component Serial # 17-18: The scan tool displays digits
17 and 18 of the driver door module (DDM) serial number.
Driver Door Ajar Sw.: The scan tool displays On/Off. This is
the state of the driver door ajar switch as detected by the driver door module. When
the driver door is open, the switch closes and the scan tool displays On. When the
driver door is closed, the switch opens and the scan tool displays Off.
Driver Door Cylinder Sw.: The scan tool displays Idle/Unlock.
This is the state of the driver door cylinder switch as detected by the driver door
module. When the door key is inserted into the driver door lock cylinder and turned
to the Unlock position, the scan tool displays Unlock. When the driver door lock cylinder
is not being turned to the Unlock position, the scan tool displays Idle.
Driver Door Jamb Sw.: The scan tool displays On/Off. This is
the state of the driver door jamb switch as detected by the driver door module. When
the driver door is opened, the switch closes and the scan tool displays On. When
the driver door is closed, the switch opens and the scan tool displays Off.
Driver Door Lock Output: The scan tool displays Idle/Lock/Unlock.
This is the driver door lock output from the driver door module to the driver door
lock actuator, where the output transitions to the lock and unlock positions are displayed
as Lock and Unlock.
Driver Door Lock Sw.: The scan tool displays Idle/Lock/Unlock.
This is the state of the driver door lock switch as detected by the driver door switch
assembly (DDSA). Switch transitions to the lock and unlock positions are displayed
as Lock and Unlock. The DDSA sends this switch status to the driver door module via
the power door serial data circuit.
Driver LF Window Sw.: The scan tool displays Idle/Up/Down/Express
Dwn. This is the state of the driver door window switch as detected by the driver
door switch assembly (DDSA). Switch transitions to the up, down and express down
positions are displayed as Up, Down and Express Dwn. The DDSA sends this switch status
to the driver door module via the power door serial data circuit.
Driver LR Window Sw.: The scan tool displays Idle/Up/Down.
This is the state of the driver left rear window switch as detected by the driver
door switch assembly (DDSA). Switch transitions to the up and down positions are
displayed as Up and Down. The DDSA sends this switch status to the driver door module
(DDM) via the power door serial data circuit.
Driver Mirror Outputs: The scan tool displays Idle/Left/Right/Up/Down/Heated
Mirror. This is the mirror output from the driver door module to the drivers side
mirror motors and mirror heating element. The output transitions indicate, either
the direction in which the mirror is being commanded to move, or the state of the
heated mirror function. Heated Mirror is displayed when the mirror is being commanded
to heat. When the mirror is not being commanded to heat, or to move in any direction,
the scan tool displays Idle.
Driver Mirror Selectors: The scan tool displays Off/Driver/Passenger.
This indicates which mirror, if any, the operator has selected for adjustment. The
driver door switch assembly (DDSA) detects the position of this switch and sends the
information to the driver door module via the power door serial data circuit.
Driver Mirror Switches: The scan tool displays Idle/Left/Right/Up/Down.
This is the state of the mirror position switch as detected by the driver door switch
assembly (DDSA). The DDSA reports this switch status to the driver door module via
the power door serial data circuit. When the switch is operated in the UP, Down, Right,
or Left directions, the scan tool displays the corresponding direction. When the switch
is not being operated, the scan tool displays Idle.
Driver RF Window Sw.: The scan tool displays Idle/Up/Down/Express
Dwn. This is the state of the driver right front window switch as detected by the
driver door switch assembly (DDSA). Switch transitions to the up, down and express
down positions are displayed as Up, Down and Express Dwn. The DDSA sends this switch
status to the driver door module via the power door serial data circuit.
Driver RR Window Sw.: The scan tool displays Idle/Up/Down.
This is the state of the driver right rear window switch as detected by the driver
door switch assembly (DDSA). Switch transitions to the up and down positions are
displayed as Up and Down. The DDSA sends this switch status to the driver door module
via the power door serial data circuit.
Driver Window Output: The scan tool displays Idle/Up/Down.
This is the driver door window output from the driver door module to the driver window
motor, where the output transitions to the up and down positions are displayed as
Up and Down.
Julian Date Of Build: The scan tool displays a four digit number
representing the day of the year the driver door module was built.
L.R. Door Lock Outputs: The scan tool displays Idle/Lock/Unlock.
This is the LR door lock output from the left rear door module to the left rear door
lock actuator, where the output transitions to the lock and unlock positions are
displayed as Lock and Unlock.
L.R. Door Window Output: The scan tool displays Idle/Up/Down.
This is the LR door window output from the left rear door module to the left rear
window motor, where the output transitions to the up and down positions are displayed
as Up and Down.
Left Rear Door Ajar Sw.: The scan tool displays On/Off. This
is the state of the left rear door ajar switch as detected by the left rear door module.
When the left rear door is opened, the switch closes and the scan tool displays On.
When the left rear door is closed, the switch opens and the scan tool displays Off.
Left Rear Door Jamb Sw.: The scan tool displays On/Off. This
is the state of the left rear door jamb switch as detected by the left rear door module.
When the left rear door is opened, the switch closes and the scan tool displays On.
When the left rear door is closed, the switch opens and the scan tool displays Off.
Lt. Horiz. Mirror Pos.: The scan tool displays 0.25-4.75 volts.
This is the driver mirror horizontal position sensor feedback voltage to the driver
door module. The voltage varies directly with the horizontal position of the driver
outside rearview mirror.
Lt. Rear Door Window Sw.: The scan tool displays Idle/Up/Down.
This is the state of the left rear door window switch as detected by the left rear
door module (LRDM). Switch transitions to the up and down positions are displayed
as Up and Down.
Lt. Vertical Mirror Pos.: The scan tool displays 0.25-4.75 volts.
This is the driver mirror vertical position sensor feedback voltage to the driver
door module. The voltage varies directly with the vertical position of the driver
outside rearview mirror.
Memory Recall Switches: The scan tool displays Idle/Memory 1/Memory
2/Exit. When the memory function switch is operated, the scan tool displays the function
selected.
Pass. Door Ajar Sw.: The scan tool displays On/Off. This is
the state of the front passenger door ajar switch as detected by the front passenger
door module (PDM). When the front passenger door is opened, the switch closes and
the scan tool displays On. When the front passenger door is closed, the switch opens
and the scan tool displays Off.
Pass. Door Cylinder Sw.: If the vehicle is equipped
with this feature, the scan tool displays Idle/Unlock. This is the state of the front
passenger door cylinder switch as detected by the front passenger door module. When
the door key is inserted into the front passenger door lock cylinder and turned to
the Unlock position, the scan tool displays Unlock. When the front passenger door
lock cylinder is not being turned to the Unlock position, the scan tool displays Idle.
Pass. Door Jamb Sw.: The scan tool displays On/Off. This is
the state of the front passenger door jamb switch as detected by the front passenger
door module. When the front passenger door is opened, the switch closes and the scan
tool displays On. When the front passenger door is closed, the switch opens and the
scan tool displays Off.
Pass. Door Lock Outputs: The scan tool displays Idle/Lock/Unlock.
This is the front passenger door lock output from the front passenger door module
to the front passenger door lock actuator, where the output transitions to the lock
and unlock positions are displayed as Lock and Unlock.
Pass. Door Lock Sw.: The scan tool displays Idle/Lock/Unlock.
This is the state of the front passenger door lock switch as detected by the front
passenger door module. Switch transitions to the lock and unlock positions are displayed
as Lock and Unlock.
Pass Door Window Output: The scan tool displays Idle/Up/Down.
This is the front passenger door window output from the front passenger door module
to the front passenger window motor, where the output transitions to the up and down
positions are displayed as Up and Down.
Pass. Door Window Sw.: The scan tool displays Idle/Up/Down/Express
Dwn. This is the state of the front passenger door window switch as detected by the
front passenger door module. Switch transitions to the up, down and express down
positions are displayed as Up, Down and Express Dwn.
Passenger Mirror Output: The scan tool displays Idle/Left/Right/Up/Down/Heated
Mirror. This is the mirror output from the front passenger door module to the passengers
side mirror motors and mirror heating element. The output transitions indicate, either
the direction in which the mirror is being commanded to move, or the state of the
heated mirror function. Heated Mirror is displayed when the mirror is being commanded
to heat. When the mirror is not being commanded to heat, or to move in any direction,
the scan tool displays Idle.
Personalization Option: This is the state of the personalization
option as it is stored in the Dash Integration Module (DIM). When Personalization
Option is selected, the scan tool displays the directions to activate or deactivate
the personalization option. An asterisk displayed beside the option indicates that
the option is activated. The personalization option is normally set to the activated
state during assembly of the vehicle.
PROM: The scan tool displays the four digit number of the PROM
incorporated into the driver door module (DDM).
R.R. Door Lock Outputs: The scan tool displays Idle/Lock/Unlock.
This is the RR door lock output from the right rear door module to the right rear
door lock actuator, where the output transitions to the lock and unlock positions
are displayed as Lock and Unlock.
R.R. Door Window Output: The scan tool displays Idle/Up/Down.
This is the RR door window output from the right rear door module to the right rear
window motor, where the output transitions to the up and down positions are displayed
as Up and Down.
Right Rear Door Ajar Sw.: The scan tool displays On/Off. This
is the state of the right rear door ajar switch as detected by the right rear door
module. When the right rear door is opened, the switch closes and the scan tool displays
On. When the right rear door is closed, the switch opens and the scan tool displays
Off.
Rt. Horiz. Mirror Pos.: The scan tool displays 0.25-4.75 volts.
This is the passengers mirror horizontal position sensor feedback voltage to the
front passenger door module. The voltage varies directly with the horizontal position
of the passenger outside rearview mirror.
Rt. Rear Door Jamb Sw: The scan tool displays On/Off. This
is the state of the right rear door jamb switch as detected by the right rear door
module. When the right rear door is opened, the switch closes and the scan tool displays
On. When the right rear door is closed, the switch opens and the scan tool displays
Off.
Rt. Rear Door Window Sw.: The scan tool displays Idle/Up/Down.
This is the state of the right rear door window switch as detected by the right rear
door module. Switch transitions to the up and down positions are displayed as Up and
Down.
Rt. Vertical Mirror Pos.: The scan tool displays 0.25-4.75 volts.
This is the passengers mirror vertical position sensor feedback voltage to the front
passenger door module. The voltage varies directly with the vertical position of the
passenger outside rearview mirror.
Window Lockout Sw.: The scan tool displays Idle/Active. This
is the driver door window lockout switch input to the driver door switch assembly
(DDSA). The DDSA sends this information via the power door serial data circuit to
the driver door module (DDM). The scan tool displays Active each time the window lockout
switch is momentarily pressed. When the feature is actived, either all three of the
passenger door window switches are locked out, or, the rear door window switches only
are locked out, depending upon driver personalization of this feature.
Year Module Built: The scan tool displays the four digit year
of build of the driver door module (DDM).