Circuit Description
The crankshaft position (CKP) sensor contains 2 hall-effect switches in one housing. This sensor configuration produces 2 separate CKP sensor pulses. These pulses occur when 2 interrupter rings, mounted to the crankshaft balancer, the outer one containing 18 evenly spaced windows and blades, the inner one containing 3 unevenly spaced windows and blades, pass by the sensors. The 18X sensor produces 18 pulses per engine revolution. The 3X sync sensor produces 3 pulses per engine revolution, each pulse representing a pair of companion cylinders. Both sensors are connected directly to the ignition control module (ICM). The sensor wiring includes the following circuits:
| • | The CKP sensor 1 signal circuit |
| • | The CKP sensor 2 signal circuit |
| • | A shared 12-volt reference circuit |
| • | A shared low reference circuit |
The ICM uses the sensors to determine the engine position and speed. A signal converter within the ICM, using the CKP sensor 1 18X pulse, produces a digital 18X output signal to the powertrain control module (PCM) on the medium resolution engine speed signal circuit. The PCM monitors the medium resolution engine speed signal circuit for errors. If the PCM does not receive a signal from the ICM, DTC P0335 sets.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0335 Crankshaft Position (CKP) Sensor A Circuit
Conditions for Running the DTC
| • | The engine run time is more than 3 seconds. |
| • | This diagnostic runs continuously when the above condition is met. |
Conditions for Setting the DTC
| • | The PCM detects the following for every 2 engine revolutions: |
| - | 6 low resolution engine speed signals |
| - | 1 camshaft position (CMP) sensor signal |
| - | 0 medium resolution engine speed signals |
| • | The above conditions are met for more than 8 seconds. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Step | Action | Values | Yes | No | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Controls Connector End Views or Powertrain Control Module Connector End Views | ||||||||||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information | ||||||||
2 | Attempt to start the engine. Does the engine start and run? | -- | Go to Step 3 | Go to Step 8 | ||||||||
3 | Observe the 18X Crank Sensor parameter with the scan tool. Does the 18X Crank Sensor parameter change with engine speed? | -- | Go to Step 4 | Go to Step 5 | ||||||||
4 |
Does the DTC fail this ignition? | -- | Go to Step 5 | Go to Intermittent Conditions | ||||||||
5 |
Does the test lamp illuminate? | -- | Go to Step 10 | Go to Step 6 | ||||||||
6 |
Does the test lamp illuminate? | -- | Go to Step 9 | Go to Step 7 | ||||||||
7 |
Does the 18X Crank Sensor RPM change? | -- | Go to Step 13 | Go to Step 11 | ||||||||
8 |
Is the voltage within the specified range? | 4-8 V | Go to Step 14 | Go to Step 12 | ||||||||
9 | Test the medium resolution engine speed signal circuit between the ICM and the powertrain control module (PCM) for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 19 | ||||||||
10 | Test the medium resolution engine speed signal circuit between the ICM and the PCM for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 19 | ||||||||
11 | Test the medium resolution engine speed signal circuit between the ICM and the PCM for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 16 | ||||||||
12 | Test the CKP sensor 2 signal circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 15 | ||||||||
13 | Inspect for the following conditions:
Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 15 | ||||||||
14 | Test for an intermittent or for poor connections at the CKP sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 17 | ||||||||
15 | Test for an intermittent or for poor connections at the ICM. Refer to Testing for Intermittent Conditions and Poor Connections , and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 18 | ||||||||
16 | Test for poor connections at the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 19 | ||||||||
17 | Replace the CKP sensor. Refer to Crankshaft Position Sensor Replacement . Did you complete the replacement? | -- | Go to Step 20 | |||||||||
18 | Replace the ICM. Refer to Ignition Control Module Replacement . Did you complete the replacement? | -- | Go to Step 20 | -- | ||||||||
19 | Replace the PCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 20 | -- | ||||||||
20 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 21 | ||||||||
21 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information | System OK | ||||||||
