Important:
| • | The
EN-48072
must be used to ensure even application of the sealant in the bore and to prevent blockage of the drain back hole. |
| • | Ensure components that are being sealed with RTV sealant are assembled within 20 minutes. Components assembled after the RTV sealant has skinned-over, approximately 20 minutes, will not bond properly. |
| • | Although originally equipped with a lip-style crankshaft rear oil seal, engines built from March 1, 1996 through 1999 should use the cassette-style crankshaft rear oil seal. |
- Ensure the engine block where the crankshaft rear oil seal is installed is a deep bore (1).
| • | A deep bore of approximately 15 mm (0.5906 in) was used on engines from March 1, 1996 and later. |
| • | A shallow bore of approximately 8 mm (0.3150 in) was used on engines from 1993 through February 29, 1996. This block would use a lip-style crankshaft rear oil seal and the
J 38817-A
for installation. |
- Inspect the engine block bore (1)
and the crankshaft flange (2) for the damage. Repair or replace any damaged components.
- Ensure the oil drain-back hole (1) is clear of debris using a wire or an unbound plastic tie
wrap (2).
Important: In order to ensure proper bonding of the sealant the bore must be clean and dry.
- Clean the bore in the block with cleaner solvent GM P/N 12378392 or 12346139 (Canadian P/N 88901247).
Important: Northstar engines 2005 and older have an 8 x 1.25 mm flywheel/flexplate crankshaft bolt hole thread. Northstar engines 2006 and later have an 11 x 1.5 mm flywheel/flexplate crankshaft bolt hole thread.
- Remove the proper sized bolts from the
J 45930-A
. Use the bolts (2) 8 mm or the bolts (3) 11 mm.
- Install the
EN-48072
pilot
base onto the crankshaft. The hub on the crankshaft will fit into the recess on the inboard side of the
EN-48072
pilot base.
Important: Northstar engines 2005 and older have an 8 x 1.25 mm flywheel/flexplate crankshaft bolt hole thread. Northstar engines 2006 and later have an 11 x 1.5 mm flywheel/flexplate crankshaft bolt hole thread.
- Use the proper bolts from the
J 45930-A
to retain the
EN-48072
pilot base in place.
- Install the
EN-48072
applicator
housing over the
EN-48072
pilot base. Ensure the
EN-48072
applicator housing bottoms in the bore of the block.
Important: The sealant must not block the drain back hole. Blockage of the drain back hole can lead to oil leakage.
- Apply the sealant GM P/N 12378521 (Canadian P/N 88901148) to the bore outer diameter in the block. Ensure the sealant does not block the drain hole.
Important: Apply steady even pressure to the
EN-48072
applicator housing.
- Using a suitable tool spread the sealant within the bore to ensure an even coating across the bore.
Important: In order to apply an even coat of the sealant do not twist or turn the
EN-48072
applicator housing as it is pulled away from the bottom of the bore.
- Using both hands, slowly and evenly, pull the
EN-48072
applicator housing out of the bore and remove it from the
EN-48072
pilot base.
- Remove the
J 45930-A
bolts
from the
EN-48072
pilot base.
- Remove the
EN-48072
pilot base.
- Ensure that the sealant (1)
is evenly spread across the bore of the block.
- Ensure the drain back hole (1) is clear of the
sealant.
Important:
| • | Beginning with the model year 2006 the flywheel/flexplate crankshaft bolt hole thread was changed from 8 x 1.25 mm to 11 x 1.5 mm. The
J 45930-A
will service the cassette seals
installed on engines from March 1, 1996 to 2006. If a J 45930 is to be used on a 2006 or later engine the update kit, J 45930-10, must be used to convert the J 45930 to a
J 45930-A
. |
| • | Crankshaft rear oil seal and engine flywheel installation requires adequate space for installation. If the engine stand does not allow suitable space to use the
J 45930-A
install the crankshaft
rear oil seal and engine flywheel with the engine properly supported on the floor or on a bench. |
| • | Northstar engines 2005 and older have an 8 x 1.25 mm flywheel/flexplate crankshaft bolt hole thread. Northstar engines 2006 and later have an 11 x 1.5 mm flywheel/flexplate crankshaft bolt hole thread. |
- Ensure the proper size of bolt (2) 8 mm or (3) 11 mm is being installed in the
J 45930-A
.
- Turn the center nut (1) of the
J 45930-A
until the center hub (2) protrudes approximately 15 mm (0.591 in) beyond the outer plate (3).
Important: DO NOT use any lubricant in order to install the crankshaft rear oil seal. Do not use any lubricant on the coating pre-applied to the inner diameter of the crankshaft rear oil seal. The coating is a sealant that must
not be contaminated. Do not use any lubricant on the outer diameter of the crankshaft rear oil seal. The sealant applied to the bore of the engine block will not properly bond to a lubricated crankshaft rear oil seal.
- Do not lubricate any part of the new cassette style crankshaft rear oil seal.
- Install the new cassette style crankshaft rear oil seal
onto the center hub of the
J 45930-A
.
- Thread the two
J 45930-A
mounting bolts into the crankshaft flywheel bolt holes.
- Tighten the two mounting bolts until
the
J 45930-A
is firmly mounted on the crankshaft.
- Install the new cassette style crankshaft
rear oil seal by turning the nut of the
J 45930-A
until the drive portion of the
J 45930-A
bottoms against the crankcase.
- Loosen the center nut to release pressure on the crankcase.
- Loosen the two mounting bolts.
- Remove the
J 45930-A
from
the crankshaft.
- Wipe off any excessive sealant from the block.
- Ensure the new cassette style crankshaft rear oil seal
is installed properly.
| • | The outer surface of the seal (3) should be 0.500-0.800 mm (0.0197-0.0315 in) (1) below the surface of the engine block (2). |
| • | The inner surface of the sleeve (6) should be 0.400-0.900 mm (0.0158-0.0354 in) (4) below the surface of the outer surface of the seal (5). |
| • | The installed seal and sleeve need to be parallel to the block by 0.000-0.500 mm (0.000-0.0197 in). |
- Clean all tools to remove any residual sealant.
- Install the flywheel. Refer to
Engine Flywheel Replacement
.
- Install the transaxle. Refer to
Transmission Replacement
.
