GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Buick 🢒 2007 🢒 Lucerne 🢒 Engine 🢒 Engine Controls and Fuel - 3.8L 🢒 DTC P0601, P0602, P0603, P0604, P0605, P0606, P0607, P1600, P1621, P1627, P1680, P1681, P1683, or P2610

Diagnostic Instructions
    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC P0601: Control Module Read Only Memory (ROM)

DTC P0602: Control Module Not Programmed

DTC P0604: Control Module Random Access Memory (RAM)

DTC P0606: Control Module Internal Performance

DTC P2610: Control Module Ignition Off Timer Performance

Description

This diagnostic applies to internal microprocessor integrity conditions within the powertrain control module (PCM) and the throttle actuator control (TAC) system. This diagnostic also addresses if the PCM is not programmed.

The PCM monitors its ability to read and write to the memory. It also monitors a timing function. The PCM and the TAC processors are used to monitor the TAC system data. Both processors monitor the other processors data to verify that the indicated accelerator pedal position (APP) calculation is correct. The PCM performs an intrusive test in order to confirm that the APP signals are not shorted together. The PCM accomplishes this by pulling the APP sensor 2 low momentarily and looking for sensor 1 to also be pulled low.

Conditions for Running the DTC

P0601

    • The ignition switch is in Run or Crank.
    • The system voltage is more than 5 volts.

P0602

    • The ignition switch is in Run or Crank.
    • The controller is identified as a service replacement PCM.

P0604

The ignition switch is in Run or Crank.

P0606

    • The ignition switch is in Run or Crank.
    • During test function after Key OFF before the control module powers down.

P2610

    • The ignition switch is in the OFF position for at least 1.6 seconds.
    • A low battery voltage or a battery disconnect condition has not taken place. Ignition OFF timer from the previous ignition cycle is stored.

Conditions for Setting the DTC

P0601

A PCM processing check value is incorrect for at least one sample. Each sample is 50 milliseconds. The PCM detects that the check value is incorrect for 0.05 second. This diagnostic runs continuous.

P0602

The PCM has not been programmed with Key ON and Engine OFF for one sample. Each sample is 100 milliseconds. The PCM has not been programmed at Key ON and Engine OFF for 0.1 second. This diagnostic runs continuous.

P0604

The PCM is unable to correctly write and read to and from random access memory (RAM) during the following conditions:

    • Key up initialization for one count. Each count is a read and write sample. Each sample is 100 milliseconds. This portion runs once per ignition cycle.
    • Counter increments by 10 for each sample that does not correctly read and write to the RAM, and decrements by one for each correct sample. No more than 20 counts which do not read and or write correctly. Each read and write sample is 100 milliseconds. This portion runs continuously.
    • Counter increments by 10 for each sample that does not correctly read and write to the Desired Throttle Position RAM and decrements by one for each correct sample. No more than 20 counts which do not read and or write correctly. Each read and write sample is 12.5 milliseconds. This portion runs continuously.

P0606

The PCM detects that the TAC system has a process sequence error, clock error, or processor is not operating correctly. Each test runs in 18.5 milliseconds. DTC sets after 200 milliseconds that a fault is detected.

P2610

This diagnostic has 2 tests that may set this DTC:

Phase 1

    • The PCM detects the ignition off timer is less than 1 second at any time.
    • The PCM detects the ignition off timer is 15 seconds or more if the actual elapsed time is less than 15 seconds.
    • This diagnostic runs continuously.

Phase 2

    • The last ignition off time event increments more than 1.375 seconds or less than 0.8 seconds for each second.
    • This diagnostic runs continuously.

Actions Taken When DTC Sets
    • DTCs P0601, P0602, P0604, and P0606 are Type A DTCs.
    • DTC P2610 is a Type B DTC.

Conditions for Clearing the MIL/DTC
    • DTCs P0601, P0602, P0604, and P0606 are Type A DTCs.
    • DTC P2610 is a Type B DTC.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

    •  Powertrain Control Module Connector End Views
    •  Engine Controls Connector End Views

Electrical Information

    •  Circuit Testing
    •  Testing for Intermittent Conditions and Poor Connections
    •  Connector Repairs
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

    •  Scan Tool Data List
    •  Scan Tool Data Definitions
    •  Scan Tool Output Controls

Circuit/System Testing
  1. Observe the DTCs with the scan tool.
    2. ⇒If DTC P0602 is set, attempt to program the PCM before replacing the PCM. Refer to Service Programming System (SPS) .
    ⇒If DTC P0602 resets, replace the PCM.
  2. Test the voltage and ground circuits to the control module for the following conditions:
    3. • A short
    • An open
    • High resistance
    ⇒If all circuits test OK, replace the PCM.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Control Module References for PCM replacement, setup, and programming.