Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC B3135 00: All Door Lock CircuitDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Driver Door Module B+ | U0199 00 | U0199 00 | -- | -- |
Door Lock/Unlock Relay B+ | 3,4 | 3,4 | -- | -- |
Front Passenger Door Module B+ | U0200 00 | U0200 00 | -- | -- |
Driver Door Latch Assembly Control | 1 | 1 | 1 | -- |
Passenger Door Latch Assembly Control | 2 | 2 | 2 | -- |
Door Lock Relay Control | B3135 00 | B3135 00 | B3135 00 | -- |
Door Unlock Relay Control | B3130 00 | B3130 00 | B3130 00 | -- |
Rear Door Latch Control | 3,4 | 3,4 | 3,4 | -- |
Door Lock/Unlock Relay Ground | -- | 3,4 | 3,4 | -- |
Driver Door Module Ground | -- | U0199 00 | 1 | -- |
Front Passenger Door Module Ground | -- | U0200 00 | 2 | -- |
1. Driver Door Latch Malfunction 2. Passenger Door Latch Malfunction 3. Rear Door Unlock Inoperative 4. Rear Door Lock Inoperative | ||||
Circuit/System Description
The body control module (BCM) internally grounds the door lock relay control circuit for the rear door lock relay when it receives a serial data message from the driver door module (DDM) or the passenger door module (PDM). When the BCM grounds the door lock relay control circuit the rear door lock relay is energized and locks the rear doors .
Conditions for Running the DTC
The system voltage is 9-16 volts.
Conditions for Setting the DTC
The BCM detects a short to ground on the door lock relay control circuit for greater than 60 seconds.
Actions Taken When the DTC Sets
The rear door lock function will be inoperative
Conditions for Clearing the DTC
| • | The DTC will be current for as long as the fault is present. |
| • | When the fault is no longer present, the DTC will be a history DTC. |
| • | A history DTC will clear after 50 ignition cycles |
Reference Information
Schematic Reference
Door Lock/Indicator Schematics
Connector End View Reference
Description and Operation
Power Door Locks Description and Operation
Electrical Information Reference
| • | Circuit Testing |
| • | Wiring Repairs |
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
Ignition ON, command the rear doors to LOCK with a scan tool. The rear doors should perform the LOCK function.
Circuit/System Testing
- Ignition OFF, disconnect the LOCK relay.
- Test for less than 15 ohms between the relay coil ground circuit terminal and ground.
- Connect a test lamp between the the relay coil control circuit terminal and the relay coil ground circuit terminal.
- Ignition ON, command the rear doors to LOCK with a scan tool. The test lamp should briefly illuminate when commanding the LOCK state.
- If the circuit tests normal, test or replace the LOCK relay.
| ⇒ | If greater than the specified range, test the ground circuit for an open/high resistance. |
| ⇒ | If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the BCM. |
| ⇒ | If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM. |
Component Testing
Relay Test
- Ignition OFF, disconnect the LOCK relay.
- Test for 60-180 ohms between terminals 85 and 86.
- Test for infinite resistance between the following terminals:
- Test for less than 2 ohms between terminals 30 and 87A.
- Install a 25A fused jumper wire between relay terminal 85 and 12 volts. Install a jumper wire between relay terminal 86 and ground. Test for less than 2 ohms between terminals 30 and 87.
| ⇒ | If not within the specified range, replace the relay. |
| • | 30 and 86 |
| • | 30 and 87 |
| • | 30 and 85 |
| • | 85 and 87 |
| ⇒ | If not the specified value, replace the relay. |
| ⇒ | If greater than the specified value, replace the relay. |
| ⇒ | If greater than the specified value, replace the relay. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for BCM replacement, setup, and programming |
