Diagnostic Instructions

DTC Descriptor

DTC P0403: Exhaust Gas Recirculation (EGR) Solenoid Control Circuit

DTC P0404: Exhaust Gas Recirculation (EGR) Open Position Performance

DTC P0405: Exhaust Gas Recirculation (EGR) Position Sensor Circuit Low Voltage

DTC P0406: Exhaust Gas Recirculation (EGR) Position Sensor Circuit High Voltage

DTC P042E: Exhaust Gas Recirculation (EGR) Closed Position Performance

Diagnostic Fault Information

Circuit	Short to Ground	Open/High Resistance	Short to Voltage	Signal Performance
5-Volt Reference	P0641, P0532, P0452, P0107	P0405	P0641	--
Sensor Signal	P0405	P0405	P0406	--
Low Reference	--	P0406	--	--
EGR Solenoid High Control	--	P0403	P0403	--
EGR Solenoid Low Control	--	P0403	--	--

Circuit Description

The engine control module (ECM) tests the exhaust gas recirculation (EGR) system during deceleration. The control module does this by momentarily commanding the EGR valve to open while monitoring the signal circuit of the manifold absolute pressure (MAP) sensor. When the EGR valve is opened, the control module will expect to see a predetermined increase in MAP. If the expected increase in MAP is not detected, the control module records the amount of MAP difference that was detected and adjusts a calibrated fail counter towards a calibrated fail threshold level. The number of EGR flow test counts required to exceed the fail threshold may vary according to the amount of detected EGR flow error.

The EGR valve position sensor is monitored by the ECM. The 5-volt reference circuit, the low reference circuit, and the EGR valve position signal circuit are used by the ECM to determine the EGR valve position. The ECM compares the EGR Position Sensor parameter with the desired EGR Position parameter when the valve is commanded open or closed.

The ECM controls the EGR valve with a solid state device called a driver. The driver supplies the EGR solenoid with 12 volts that is pulse width modulated (PWM) through the EGR solenoid high control circuit. A ground path is provided by the ECM through the EGR solenoid low control circuit.

When the ignition switch is turned ON, the ECM records the EGR Learned Minimum Position. The ECM compares the EGR Learned Minimum Position parameter to the EGR Position Sensor parameter.

Conditions for Running the DTC

P0403, P0404, P0405, P0406, P042E

P0404

P0405

DTC P0641 and P0651 are not set.

P0406

P042E

DTC P0641 and P0651 are not set.

Conditions for Setting the DTC

P0403

The ECM detects an electrical malfunction in the EGR solenoid high control circuit or the EGR solenoid low control circuit for more than 10 seconds.

P0404

The difference between the EGR Position Sensor and the desired EGR Position is more than 15 percent for more than 34 seconds.

P0405

P0406

The EGR position sensor voltage is more than 4.77 volts for more than 18 seconds.

P042E

Action Taken When the DTC Sets

DTC P0403, P0404, P0405, P0406, and P042E are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTC P0403, P0404, P0405, P0406, and P042E are Type B DTCs.

Diagnostic Aids

Inspect for excessive deposits on the EGR valve pintle or seat. Remove the EGR valve and inspect for deposits that may interfere with the EGR valve pintle extending completely or cause the pintle to stick.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Exhaust Gas Recirculation (EGR) System Description

Electrical Information Reference

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

Important: If DTC P0641 or P0652 are also set, diagnose those DTCs first.

1. With the ignition ON and the engine OFF, command the EGR from 0-90 percent. The EGR Position Sensor parameter should remain within 3 percent of the Desired EGR Position parameter through the entire range.
2. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

Important: You must complete the Circuit/System Verification before proceeding with Circuit/System Testing.

1. Ignition OFF, disconnect the EGR valve harness connector.
2. Ignition ON, connect a test lamp between B+ and the EGR low control circuit. The test lamp should illuminate.

⇒	If the test lamp does not illuminate, test the EGR low control circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

3. Connect a test lamp between the EGR high control circuit and ground. Command the EGR valve from 0-90 percent and exit the EGR Solenoid Output Control. The test lamp should turn ON when commanded between 10 and 90 percent and turn OFF when exiting the EGR Solenoid Output Control.

⇒	If the test lamp is ON after exiting the EGR Solenoid Output Control, test the EGR high control circuit for a short to voltage. If the circuit tests normal, replace the ECM.

⇒	If the test lamp is always OFF while commanding the EGR valve from 0-90 percent, test the EGR high control circuit for an open, high resistance, or a short to ground. If the circuit tests normal, replace the ECM.

4. Ignition OFF, test for less than 1 ohm of resistance between the low reference circuit and ground.

⇒	If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

5. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit and ground.

⇒	If less than the specified range, test the 5-volt reference circuit for a short to ground, short to EGR Control circuits or an open/high resistance. If the circuit tests normal, replace the ECM.

⇒	If greater than the specified range, test the 5-volt reference circuit for a short to voltage . If the circuit tests normal, replace the ECM.

6. Verify the EGR Position parameter is less than 1 percent.

⇒	If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the ECM.

7. Install a 3A fused jumper wire between the signal circuit and the 5-volt reference circuit . The EGR Position Sensor parameter should display more than 99 percent.

⇒	If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.

8. If all circuits test normal, replace the EGR Valve.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.