GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Buick 🢒 1999 🢒 Park Avenue 🢒 DTC 🢒 DTC B2201 LF Window Switch Stuck in Down Position

Object Number: 324026 Size: MF
Power Door Systems Components
Cell 120: Front Power Window Components
Handling ESD Sensitive Parts Notice

Circuit Description

The simple bus interface, CKT 217 (LT BLU), provides a communications path from the LH front power window switch to the driver door module (DDM).The DDM contains the following two types of software:

    • Switch message decoding software
    • Simple bus interface diagnostic software

The software enables the DDM to monitor the state of the LH front power window switch.

Conditions for Setting the DTC

DTC B2201 sets any time one of the driver door power window switches is continuously closed in either UP or DOWN positions for a period greater than 15 seconds.

DTCs B1982 (battery Voltage High) and B1983 (Battery Voltage Low) must not be current or the diagnostic will not run.

Action Taken When the DTC Sets

The switch command will be ignored until it again changes state or the ignition cycles from OFF to RUN.

Conditions for Clearing the MIL/DTC
    • This DTC will set from current to history when the window up input cycles off or when the power mode changes from OFF to RUN.
    • The history DTC will clear after 50 ignition cycles.
    • Use a scan tool in order to clear a history DTC.

Diagnostic Aids
    • A history DTC is evidence of an intermittent condition.
    • If DTC B2201 is current, cycle the ignition switch from OFF to RUN. If this DTC is still current, replace the LH front power window switch assembly. The individual power window switches are an integral part of the LH front power window switch assembly. The individual power window switches cannot be replaced separately. Refer to Front Side Door Window Switch Replacement .

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. Perform the Power Door Diagnostic System Check prior to continuing the diagnosis of this DTC.

    2.

  2. This step tests for other set DTCs.

    3.

  3. This step verifies the operation of all of the power windows.

    4.

  4. This step tests the LH front power window switch.

B2201 LF Window Switch Stuck in The Down Position

Step

Action

Value(s)

Yes

No

1

Did you perform the Power Door Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check - Power Door Systems

2

Inspect the scan tool for the following DTCs:

    • B2200
    • B2201
    • B2212
    • B2213
    • B2214
    • B2215
    • B2216
    • B2217

Are all of the above DTCs set?

--

Go to Step 6

Go to Step 3

3

  1. Install the scan tool.
  2. Go to the driver door module (DDM) special functions.
  3. Use the scan tool in order to command all of the windows up and down.

Do all of the windows function properly?

--

Go to Step 5

Go to Step 6

4

Replace the LH front power window switch. Refer to Front Side Door Window Switch Replacement

Is the repair complete?

--

Go to Step 7

--

5

  1. Turn ON the ignition.
  2. Press any driver door window switch except the switch with the set DTC.

Do windows function properly?

--

Go to Step 4

Go to Diagnostic System Check - Power Door Systems

6

Replace the DDM. Refer to Front Door Module Replacement

Is the repair complete?

--

Go to Step 7

--

7
  1. Turn OFF the ignition switch.
  2. Reconnect or install any connectors or components that were disconnected or removed.
  3. Turn ON the ignition switch.
  4. Clear any DTCs.

Are all of the DTCs cleared?

--

Go to Diagnostic System Check - Power Door Systems

--