Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Power Window Schematics and Door Control Module Schematics Connector End View Reference: Master Electrical Component List in Wiring Systems DEFINITION: This test is to be used to diagnose either an inoperative driver door window or a passenger door window that is only inoperative from the driver door. | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
2 | Verify that the Power Window Inoperative from Master Switch complaint is present. Does the Power Window System operate from the master switch, driver door switch assembly (DDSA), as described in the Power Windows Description and Operation? | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 |
3 |
Did the parameters change from the Idle to the Up, Down, and Express states? | Go to Step 4 | Go to Step 12 |
4 | Is the driver door window inoperative? | Go to Step 5 | |
5 |
Does the test lamp illuminate? | Go to Step 6 | Go to Step 11 |
6 |
Does the test lamp illuminate? | Go to Step 7 | Go to Step 9 |
7 |
Does the test lamp illuminate? | Go to Step 8 | Go to Step 10 |
8 |
Does the test lamp illuminate in both the UP and DOWN positions? | Go to Step 13 | Go to Step 14 |
9 | Test the power window motor left front up circuit for a short to ground, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 19 | Go to Step 14 |
10 | Test the power window motor left front down circuit for a short to ground, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 19 | Go to Step 14 |
11 | Test the battery positive voltage circuit of connector C2 of the DDM for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 19 | Go to Step 15 |
12 | Inspect for poor connections at the DDSA harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 19 | Go to Step 16 |
13 | Inspect for poor connections at the driver door power window motor harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 19 | Go to Step 17 |
14 | Inspect for poor connections at the DDM harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 19 | Go to Step 18 |
15 | Repair the open in the ground circuit of connector C2 of the DDM. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | Go to Step 19 | -- |
16 | Replace the inoperative DDSA. Refer to Front Door Switch Replacement . Did you complete the replacement? | Go to Step 19 | -- |
17 | Replace the inoperative driver door power window motor. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | Go to Step 19 | -- |
18 | Replace the inoperative DDM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | Go to Step 19 | -- |
19 | Operate the system in order to verify the repair. Did you correct the condition? | System OK | Go to Step 2 |
