GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Buick 🢒 2005 🢒 Park Avenue 🢒 Body 🢒 Stationary Windows 🢒 Automatic Day-Night Mirrors Inoperative

Step

Action

Value(s)

Yes

No

Schematic Reference: Inside Rearview Mirror Schematics and Outside Rearview Mirror Schematics in Doors

Component End View Reference: Stationary Windows Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2
  1. Turn ON the ignition, with the engine OFF.
  2. Turn OFF the automatic day-night feature of the inside rearview mirror.
  3. Observe the driver outside rearview mirror.

Does the driver outside rearview mirror remain in a darken state?

--

Go to Step 22

Go to Step 3

3
  1. Turn ON the automatic day-night feature of the inside rearview mirror.
  2. Cover the sensor on the inside rearview mirror back, facing the front window.
  3. Shine a bright light into the sensor on the inside rearview mirror face, facing the rear window.

Does the inside rearview mirror darken?

--

Go to Step 4

Go to Step 5

4

While shining a bright light into the sensor on the mirror face, facing the rear window, observe the driver outside rearview mirror.

Does the driver outside rearview mirror darken?

--

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 9

5
  1. Turn OFF the ignition.
  2. Disconnect the harness connector of the inside rearview mirror.
  3. Measure the resistance between the ground circuit of the inside rearview mirror and ground.

Is the resistance less than the specified value?

3 ohms

Go to Step 6

Go to Step 20

6
  1. Turn ON the ignition, with the engine OFF.
  2. Measure the voltage between the ignition voltage circuit and the ground circuit of the inside rearview mirror.

Is the voltage within the specified range?

9-16 V

Go to Step 7

Go to Step 21

7
  1. Place the transmission in PARK.
  2. Measure the voltage between the backup lamp supply voltage circuit and the ground circuit of the inside rearview mirror.

Is the voltage less than the specified value?

0.5 V

Go to Step 8

Go to Backup Lamps Always On in Lighting Systems

8
  1. Place the transmission in REVERSE.
  2. Measure the voltage between the backup lamp supply voltage circuit and the ground circuit of the inside rearview mirror.

Is the voltage within the specified range?

9-16 V

Go to Step 16

Go to Step 13

9
  1. Turn OFF the ignition.
  2. Disconnect the harness connector C1 of the driver door module (DDM).
  3. Turn ON the ignition, with the engine OFF.
  4. Turn ON the automatic day-night feature of the inside rearview mirror.
  5. Cover the sensor on the mirror back, facing the front window.
  6. Shine a bright light into the sensor on the mirror face, facing the rear window.
  7. Measure the voltage between the automatic day-night signal circuit and the low reference circuit of the driver outside mirror element.

Is the voltage within the specified range?

0.75-1.5 V

Go to Step 11

Go to Step 10

10

Measure the voltage between the automatic day-night signal circuit of the driver outside mirror element and a good ground.

Is the voltage within the specified range?

0.75-1.5 V

Go to Step 15

Go to Step 14

11
  1. Turn OFF the ignition.
  2. Disconnect the harness connector C4 of the DDM.
  3. Connect a 3-amp fused jumper wire between harness connectors C1 and C4 for the automatic day-night signal circuit of driver outside rearview mirror element.
  4. Connect a 3-amp fused jumper wire between harness connectors C1 and C4 for the low reference circuit of driver outside rearview mirror element.
  5. Turn ON the ignition, with the engine OFF.
  6. Turn ON the automatic day-night feature of the inside rearview mirror.
  7. Cover the sensor on the mirror back, facing the front window.
  8. Shine a bright light into the sensor on the mirror face, facing the rear window.
  9. While shining a bright light into the sensor on the mirror face, facing the rear window, observe the driver outside rearview mirror.

Does the driver outside rearview mirror darken?

--

Go to Step 17

Go to Step 12

12
  1. Turn OFF the ignition.
  2. Carefully disconnect the driver outside rearview mirror face. Refer to Outside Rearview Mirror Glass Replacement .
  3. Turn ON the ignition, with the engine OFF.
  4. Turn ON the automatic day-night feature of the inside rearview mirror.
  5. Cover the sensor on the mirror back, facing the front window.
  6. Shine a bright light into the sensor on the mirror face, facing the rear window.
  7. Measure the voltage between the signal circuit and the low reference circuit of the driver outside mirror element.

Is the voltage within the specified range?

0.75-1.5 V

Go to Step 18

Go to Step 19

13

Test the backup lamp supply voltage circuit of the inside rearview mirror for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 27

Go to Backup Lamps Inoperative in Lighting Systems

14

Test the automatic day-night signal circuit of the driver outside rearview mirror element for an open or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find or correct the condition?

--

Go to Step 27

Go to Step 16

15

Test the low reference circuit of the driver outside rearview mirror element for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find or correct the condition?

--

Go to Step 27

Go to Step 16

16

Inspect for poor connections at the harness connector of the inside rearview mirror. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 27

Go to Step 23

17

Inspect for poor connections at the harness connector of the DDM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find or correct the condition?

--

Go to Step 27

Go to Step 24

18

Inspect for poor connections at the harness connector of the driver outside rearview mirror face. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find or correct the condition?

--

Go to Step 27

Go to Step 25

19

Inspect for poor connections at the harness connector of the driver outside rearview mirror. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find or correct the condition?

--

Go to Step 27

Go to Step 26

20

Repair an open or high resistance in the ground circuit of the inside rearview mirror. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

--

Go to Step 27

--

21

Repair an open or short to ground in the ignition voltage circuit of the inside rearview mirror. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

--

Go to Step 27

--

22

Important:: A short to battery positive voltage on the automatic day-night signal circuit of the driver outside rearview mirror element will cause permanent damage to the driver outside rearview mirror and the inside rearview mirror. Both mirrors will have to replaced. The following actions will need to be performed:

  1. Repair a short to battery positive voltage on the automatic day-night signal circuit of the driver outside rearview mirror element. Refer to Wiring Repairs in Wiring Systems.
  2. Replace the following:
    3. • Driver outside rearview mirror face. Refer to Outside Rearview Mirror Glass Replacement in Doors.
    • Inside rearview mirror. Refer to Control Module References in Computer/Integrating Systems for replacement, setup and programming.

Did you complete the repair?

--

Go to Step 27

--

23

Replace the inside rearview mirror. Refer to Control Module References in Computer/Integrating Systems for replacement, setup and programming.

Did you complete the replacement?

--

Go to Step 27

--

24

Replace the DDM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup and programming.

Is the replacement complete?

--

Go to Step 27

--

25

Replace the driver outside rearview mirror face. Refer to Outside Rearview Mirror Glass Replacement .

Did you complete the replacement?

--

Go to Step 27

--

26

Replace the driver outside rearview mirror. Refer to Power Mirror Replacement .

Did you complete the replacement?

--

Go to Step 27

--

27

Operate the system in order to verify the repair.

Did you correct the condition?

--

System OK

Go to Step 2