Cruise Control Description and Operation 4.2L
Cruise control is a speed control system that maintains a desired vehicle speed
under normal driving conditions at vehicle speeds above 40 km/h (25 mph).
Steep grades may cause variations in the selected vehicle speeds.
The following are the main components of the Cruise Control System:
| • | The powertrain control module (PCM) |
| • | The Resume/Accel switch |
| • | The throttle actuator control (TAC) motor |
| • | The vehicle speed sensor |
Cruise Control Engaged
The cruise control system will engage and adjust the vehicle speed based on
the activation of the following cruise control switches:
The cruise control switches are located on the multifunction/turn signal lever.
The powertrain control module (PCM) monitors the signal circuits of the cruise
control switches in order to determine when to capture and maintain the selected
vehicle speed. The PCM uses the throttle actuator control (TAC) module motor in order
to control the vehicle speed. For further information on the TAC System, refer to
Throttle Actuator Control (TAC) System Description
in
Engine Controls - 4.2 L.
Ignition positive voltage is supplied from the 10 ampere HVAC 1
fuse to the cruise control switch via the ignition 3 voltage circuit. When
the normally open cruise control On/Off switch is turned On, the switch closes and
the PCM detects a high signal voltage on the cruise control on switch signal circuit.
When the normally open Set/Coast switch is pressed, the switch closes and the PCM
detects a high signal voltage on the cruise control set/coast switch signal circuit.
To engage the cruise control system, turn the On/Off switch On and momentarily press
the Set/Coast switch. The PCM will confirm that the cruise control enable criteria
has been achieved. The PCM will engage the cruise control system and record the selected
vehicle speed. The PCM sends a class 2 message to the instrument panel cluster
in order to illuminate the cruise control indicator. Pressing the accelerator pedal,
while the cruise control system is engaged, will allow the driver to override the
cruise control system in order to accelerate the vehicle beyond the current set vehicle
speed. When the accelerator pedal is released, the vehicle will decelerate and resume
the current set vehicle speed. The driver can also override the current set vehicle
speed via the Set/Coast switch and the Resume/Accel switch. When the cruise control
system is engaged, pressing and holding the Set/Coast switch will allow the vehicle
to decelerate from the current set vehicle speed without deactivating the cruise control
system. When the Set/Coast switch is released, the PCM will record the vehicle speed
and maintain the vehicle speed as the new set vehicle speed. When the cruise control
system is engaged, momentarily pressing the Set/Coast switch will allow the vehicle
to decelerate at 1.6 km/h (1 mph) increments for each time that the
Set/Coast is momentarily pressed, with a minimum vehicle speed of 37 km/h (23 mph).
When the normally open Resume/Accel switch is activated, the switch closes and the
PCM detects a high signal voltage on the cruise control resume/accel switch signal
circuit. Activating and holding the Resume/Accel switch, when the cruise control system
is engaged, will allow the vehicle to accelerate to a greater vehicle speed than the
current set vehicle speed. When the Resume/Accel switch is released, the PCM will
record the vehicle speed and maintain the vehicle speed as the new set vehicle speed.
When the cruise control system is engaged, momentarily activating the Resume/Accel
switch will allow the vehicle to accelerate at 1.6 km/h (1 mph) increments
for each time that the Resume/Accel switch is momentarily activated, with the maximum
acceleration total of 16 km/h (10 mph) over the current set vehicle
speed . Momentarily activating the Resume/Accel switch, after the cruise control system
has been disengaged by pressing the brake pedal, will recall the previous set vehicle
speed that is recorded in the PCM.
Cruise Control Disengaged
The PCM disengages the cruise control operation based on the signals from the
following switches:
The TCC brake switch and the stop lamp switch are incorporated into an assembly
and are mounted to the brake pedal bracket. Pressing the brake pedal while the cruise
control is engaged will disengaged the cruise control system. The PCM monitors the
TCC brake switch/cruise control release signal circuit and the stoplamp switch signal
circuit. When the brake pedal is pressed, the normally closed TCC brake switch opens
and the normally open stoplamp switch closes. The PCM detects a low signal voltage
on the TCC brake switch/cruise control release signal circuit and detects a high signal
voltage on the stop lamp switch signal circuit. The cruise control system will disengage
when the cruise control On/Off switch is turned Off. The vehicle speed stored in the
memory of the PCM will be erased when the cruise control On/Off switch is turned to
Off, or the ignition switch is turned off.
The cruise control system will disengage when the PCM detects that the driver
has the accelerator pedal override active for approximately 60 seconds.
When the cruise control system is disengaged, the PCM sends a class 2
message to the IPC in order to deactivate the cruise control indicator.
Cruise Control Inhibited
The PCM inhibits the cruise control operation when any of the following conditions
exist:
| • | The PCM detects that the center high mounted stop lamp (CHMSL) is not
operating properly. |
| • | A Cruise Control System related DTC has been set. |
| • | The vehicle speed is less than 40 km/h (25 mph). |
| • | The vehicle is in PARK, REVERSE, NEUTRAL, or 1st gear. |
| • | The engine RPM is high. |
| • | The vehicle speed is to high. |
| • | The system voltage is not between 6 volts and 16 volts. |
| • | The antilock brake system/traction control system is active for more than
2 seconds. |
Cruise Control Description and Operation 5.3L
Cruise control is a speed control system that maintains a desired vehicle speed
under normal driving conditions at vehicle speeds above 40 km/h (25 mph).
Steep grades may cause variations in the selected vehicle speeds.
The following are the main components of the cruise control system:
| • | The powertrain control module (PCM) |
| • | The Resume/Accel switch |
| • | The throttle actuator control (TAC) module |
| • | The vehicle speed sensor |
Cruise Control Engaged
The TAC module monitors the signal circuits of the following cruise control
switches:
The PCM will engage and adjust vehicle speed based on the information received
from the TAC module via the UART serial data link. For further information on the
TAC system, refer to
Throttle Actuator Control (TAC) System Description
in Engine Controls - 4.8L, 5.3L, and 6.0L.
The cruise control switches are located on the multifunction/turn signal lever.
Ignition positive voltage is supplied from the 10 ampere CRUISE fuse
to the cruise control switch via the ignition 3 voltage circuit. When the
normally open cruise control On/Off switch is turned On, the switch closes and the
TAC module detects a high signal voltage on the cruise control on switch signal circuit.
When the normally open Set/Coast switch is pressed, the switch closes and the TAC
module detects a high signal voltage on the cruise control set/coast switch signal
circuit. To engage the cruise control system, turn the On/Off switch On and momentarily
press the Set/Coast switch. The TAC sends a UART message to the PCM, in order to confirm
that the cruise control enable criteria has been met. The PCM will engage the cruise
control system and record the selected vehicle speed. The PCM sends a class 2
message to the instrument panel cluster in order to illuminate the cruise control
indicator. Pressing the accelerator pedal, while the cruise control system is engaged,
will allow the driver to override the cruise control system in order to accelerate
the vehicle beyond the current set vehicle speed. When the accelerator pedal is released,
the vehicle will decelerate and resume the current set vehicle speed. The driver can
also override the current set vehicle speed via the Set/Coast switch and the Resume/Accel
switch. When the cruise control system is engaged, pressing and holding the Set/Coast
switch will allow the vehicle to decelerate from the current set vehicle speed without
deactivating the cruise control system. When the Set/Coast switch is released, the
PCM will record the vehicle speed and maintain the vehicle speed as the new set vehicle
speed. When the cruise control system is engaged, momentarily pressing the Set/Coast
switch will allow the vehicle to decelerate at 1.6 km/h (1 mph) increments
for each time that the Set/Coast is momentarily pressed, with a minimum vehicle speed
of 37 km/h (23 mph). When the normally open Resume/Accel switch is activated,
the switch closes and the TAC module detects a high signal voltage on the cruise control
resume/accel switch signal circuit. Activating and holding the Resume/Accel switch,
when the cruise control system is engaged, will allow the vehicle to accelerate to
a greater vehicle speed than the current set vehicle speed. When the Resume/Accel
switch is released, the PCM will record the vehicle speed and maintain the vehicle
speed as the new set vehicle speed. When the cruise control system is engaged, momentarily
activating the Resume/Accel switch will allow the vehicle to accelerate at 1.6 km/h
(1 mph) increments for each time that the Resume/Accel switch is momentarily
activated, with the maximum acceleration total of 16 km/h (10 mph) over
the current set vehicle speed. Momentarily activating the Resume/Accel switch, after
the cruise control system has been disengaged by pressing the brake pedal, will recall
the previous set vehicle speed that is recorded in the PCM.
Cruise Control Disengaged
The PCM disengages the cruise control operation based on the information received
from the TAC module. The TAC module monitors the signal circuits of the following
switches:
The TCC brake switch and the stop lamp switch are incorporated into an assembly
and are mounted to the brake pedal bracket. Pressing the brake pedal while the cruise
control is engaged will disengaged the cruise control system. The TAC module monitors
the stop lamp switch signal circuit and the PCM monitors the TCC brake switch/cruise
control release signal circuit. When the brake pedal is pressed, the normally closed
TCC brake switch opens and the normally open stoplamp switch closes. The TAC module
detects a high signal voltage on the stop lamp switch signal circuit and the PCM detects
a low signal voltage on the TCC brake switch/cruise control release signal circuit.
The TAC module sends a UART message to the PCM indicating the status of the stop lamp
switch. The cruise control system will disengage when the cruise control On/Off switch
is turned Off. The vehicle speed stored in the memory of the PCM will be erased when
the cruise control On/Off switch is turned to Off, or the ignition switch is turned
off.
The cruise control system will disengage when the PCM detects that the driver
has the accelerator pedal override active for approximately 60 seconds.
When the cruise control system is disengaged, the PCM sends a class 2
message to the IPC in order to deactivate the cruise control indicator.
Cruise Control Inhibited
The PCM inhibits the cruise control operation when any of the following conditions
exist:
| • | A cruise control system related DTC has been set. |
| • | The vehicle speed is less than 40 km/h (25 mph). |
| • | The vehicle is in PARK, REVERSE, NEUTRAL, or 1st gear. |
| • | The engine RPM is high. |
| • | The vehicle speed is to high. |
| • | The system voltage is not between 6 volts and 16 volts. |
| • | The antilock brake system/traction control system is active for more than
2 seconds. |
