SERVICE MANUAL UPDATE SEC. 3C TOOL FOR STRUT CART. REMOVAL. Buick Regal 1991

SERVICE MANUAL UPDATE

SECTION 3C

MODELS AFFECTED:

1991 CHEVROLET LUMINA PAGE 3C-2 1991 PONTIAC GRAND PRIX PAGE 3C-2 1991 OLDSMOBILE CUTLASS SUPREME PAGE 3C-2 1991 BUICK PAGE 3C-2

1990 CHEVROLET LUMINA PAGE 3C-4 1990 PONTIAC GRAND PRIX PAGE 3C-3 1990 OLDSMOBILE CUTLASS SUPREME PAGE 3C-3 1990 BUICK REGAL PAGE 3C-3

1989 PONTIAC GRAND PRIX PAGE 3C-3 1989 OLDSMOBILE CUTLASS SUPREME PAGE 3C-3 1989 BUICK REGAL PAGE 3C-3

1988 PONTIAC GRAND PRIX PAGE 3C-1 1988 OLDSMOBILE CUTLASS SUPREME PAGE 3C-1 1988 BUICK REGAL PAGE 3C-4

THE FOLLOWING PROCEDURE HAS BEEN REVISED TO INCLUDE A NEW SPECIAL TOOL (J 38844). J 38844 WILL BE SHIPPED AS PART OF THE 1991 ESSENTIAL TOOL PROGRAM. THIS TOOL WAS DEVELOPED TO ELIMINATE THE POSSIBILITY OF THE FRONT SUSPENSION SPRING MOVING OUT OF ALIGNMENT WHEN REMOVING THE STRUT CARTRIDGE.

STRUT CARTRIDGE

FIGURES 1 THROUGH 9

TOOLS REQUIRED:

J 38844 STRUT ALIGNMENT TOOL J 35668 STRUT EXTENSION ROD J 35669 STRUT ROD NUT REMOVER AND INSTALLER J 35671 STRUT CAP NUT WRENCH

CAUTION:

DO NOT SERVICE THE STRUT CARTRIDGE UNLESS THE WEIGHT OF THE VEHICLE IS ON THE SUSPENSION. THE WEIGHT OF THE VEHICLE KEEPS THE COIL SPRING COMPRESSED, OTHERWISE THE RELEASED COIL SPRING COULD CAUSE PERSONAL INJURY.

REMOVE OR DISCONNECT

1. SCRIBE STRUT COVER TO BODY TO ASSURE PROPER CAMBER ADJUSTMENT.

2. STRUT MOUNT COVER PLATE (2) BY REMOVING THREE COVER PLATE NUTS (1), REFER TO FIGURE 1. 3. STRUT SHAFT NUT (4) USING NO. 50 TORX BIT AND J 35669, REFER TO FIGURE 2. 4. STRUT MOUNT BUSHING (5) BY PRYING WITH SUITABLE TOOL, REFER TO FIGURE 3. - USE J 35668 TO APPLY PRESSURE ON STRUT SHAFT (13) AS NECESSARY TO RELIEVE BUSHING (COMPRESSION) SIDE LOAD. 5. JOUNCE BUMPER (7) BY ATTACHING J 35668 TO STRUT SHAFT AND PULLING OUT JOUNCE BUMPER. REFER TO FIGURE 4. 6. INSTALL J 38844, REFER TO FIGURE 5. - USE INFORMATION SHOWN ON LABEL OF J 38844 TO INSTALL IN CORRECT POSITION. REFER TO FIGURE 6. 7. COMPRESS STRUT SHAFT (13) DOWN INTO CARTRIDGE, REFER TO FIGURE 7. 8. STRUT CARTRIDGE CLOSURE NUT (14) BY UNSCREWING CLOSURE NUT USING J 35671, REFER TO FIGURE 8. 9. STRUT CARTRIDGE (111), REFER TO FIGURE 9. 10. OIL FROM STRUT TUBE USING SUCTION DEVICE.

INSTALL OR CONNECT

1. SELF-CONTAINED REPLACEMENT CARTRIDGE (111). 2. STRUT CARTRIDGE CLOSURE NUT (14) USING J 35671. TIGHTEN - STRUT CLOSURE NUT TO 110 N.M (82 LBS. FT.). 3. INSTALL J 35668. 4. REMOVE J 38844. 5. JOUNCE BUMPER (7). 6. RAISE STRUT SHAFT AND REMOVE J 35668. 7. STRUT MOUNT BUSHING (5). - USE A SOAP SOLUTION TO LUBRICATE BUSHING FOR EASE OF INSTALLATION. - IF NECESSARY, INSTALL J 35668 AFTER BUSHING IS PARTIALLY INSTALLED AND POSITION STRUT SHAFT AS REQUIRED TO ASSIST IN BUSHING INSTALLATION. 8. STRUT SHAFT NUT (4) USING NO. 50 TORX BIT AND J 35669. TIGHTEN - STRUT SHAFT NUT TO 98 N.M (72 LBS. FT.). 9. STRUT MOUNT COVER AND NUTS. - ALIGN SCRIBE MARKS. TIGHTEN - COVER NUTS TO 24 N.M (18 LBS. FT.)

Object Number: 91844 Size: MF

Object Number: 91843 Size: MF

Object Number: 91304 Size: MF

Object Number: 91303 Size: MF

Object Number: 91842 Size: SF

Object Number: 91841 Size: MF

Object Number: 92470 Size: MF

Object Number: 91840 Size: SF

Object Number: 91839 Size: MF

General Motors bulletins are intended for use by professional technicians, not a "do-it-yourselfer". They are written to inform those technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions and know-how to do a job properly and safely. If a condition is described, do not assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See a General Motors dealer servicing your brand of General Motors vehicle for information on whether your vehicle may benefit from the information.