DTC P0134 HO2S Circuit Insufficient Activity Sensor 1. Buick Regal 1997

For 1990-2009 cars only

Makes 🢒 Buick 🢒 1997 🢒 Regal 🢒 Engine 🢒 Engine Controls - 3.8L 🢒 DTC P0134 HO2S Circuit Insufficient Activity Sensor 1

Engine Controls Components Component Locations
Engine Data Sensors-HO2S #1, HO2S #2
OBD II Symbol Description Notice

Circuit Description

The PCM supplies a bias voltage of about 450 mV between the HO2S signal and low circuits. When measured with a 10 megohm digital voltmeter, this may display as low as 320 mV. The oxygen sensor varies the voltage within a range of about 1000 mV when the exhaust is rich, down through about 10 mV when exhaust is lean. The PCM constantly monitors the HO2S signal during closed loop operation and compensates for a rich or lean condition by decreasing or increasing injector pulse width as necessary. If the HO2S 1 voltage remains at or near the 450 mV bias for an extended period of time, DTC P0134 will be set, indicating an open sensor signal or sensor low circuit.

Conditions for Running the DTC

•	No TP sensor, EVAP system, misfire, IAT sensor, MAP sensor, fuel trim, fuel injector circuit, EGR Pintle Position, ECT sensor, CKP Sensor, or MAF sensor DTC(s) present.

•	Engine run time longer than 200 seconds.

Conditions for Setting the DTC

HO2S 1 signal voltage remains between 400 mV and 500 mV for longer than 30 seconds.

Action Taken When the DTC Sets

•	The PCM will illuminate the MIL during the second consecutive trip in which the diagnostic test has been run and failed.

•	The PCM will store conditions which were present when the DTC set as Freeze Frame and Fail Records data.

Conditions for Clearing the MIL/DTC

•	The PCM will turn the MIL OFF during the third consecutive trip in which the diagnostic has been run and passed.

•	The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.

•	The DTC can be cleared by using the scan tool Clear Info function or by disconnecting the PCM battery feed.

Diagnostic Aids

Check for the following conditions:

•	Poor connection or damaged harness. Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, poor terminal to wire connection, and damaged harness.

•

Malfunctioning HO2S heater or heater circuit. With the ignition ON, engine not running, the HO2S voltage displayed on a scan tool should gradually drop to below 250 mV or rise to above 600 mV. If not, disconnect the HO2S and connect a test light between the HO2S ignition feed and heater ground circuits. If the test light does not light, repair the open ignition feed or sensor ground circuit as necessary. Refer to Repair Procedures in Electrical Diagnosis. If the test light lights and the HO2S signal and low circuits are OK, replace the HO2S.

•	Intermittent test. With the ignition ON, monitor the HO2S signal voltage while moving the wiring harness and related connectors. If the malfunction is induced, the HO2S signal voltage will change. This may help isolate the location of the malfunction.

Review the Fail Records vehicle mileage since the diagnostic test last failed to help determine how often the condition that caused the DTC to be set occurs. This may assist in diagnosing the condition.

Test Description

Number(s) below refer to the step number(s) on the Diagnostic Table

This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is being replaced, the new PCM must be programmed.

DTC P0134 - HO2S Circuit Insufficient Activity Sensor 1

Step	Action	Value(s)	Yes	No
1	Was the Powertrain On-Board Diagnostic (OBD) System Check performed?	--	Go to Step 2	Go to the Powertrain On Board Diagnostic (OBD) System Check
2	Engine at operating temperature. Operate the engine above 1200 RPM for two minutes while monitoring HO2S 1 voltage on the scan tool. Does the scan tool indicate HO2S 1 voltage varying outside the specified values?	400-500 mV	Go to Step 3	Go to Step 4
3	Turn ON the ignition switch. Review and record scan tool Fail Records data and note parameters. Operate the vehicle within Fail Records conditions as noted. Using a scan tool, monitor Specific DTC info for DTC P0134 until the DTC P0134 test runs. Does the scan tool indicate DTC failed this ignition?	--	Go to Step 4	Go to Diagnostic Aids
4	Turn ON the ignition switch. Disconnect HO2S 1 and jumper the HO2S signal and low circuits (PCM side) to ground. Using a scan tool, monitor HO2S 1 voltage. Is HO2S 1 voltage less than the specified value?	150 mV	Go to Step 8	Go to Step 5
5	Remove the jumper wire from the HO2S signal circuit (leave the HO2S low circuit jumpered to ground). Using a J 39200 Digital Multimeter, measure voltage between the HO2S 1 signal circuit (PCM side) and the HO2S 1 heater ground circuit. Does HO2S 1 signal voltage measure near the specified value?	400 mV	Go to Step 6	Go to Step 7
6	Turn OFF the ignition switch. Disconnect the PCM. Check continuity of the HO2S 1 low circuit between the PCM harness connector and the HO2S 1 harness connector. If the HO2S 1 low circuit measures over 5 ohms, repair open or poor connection as necessary (refer to Heated Oxygen Sensor (O2S) Repair in Electrical Diagnosis). Was a problem found?	--	Go to Step 13	Go to Step 9
7	Turn OFF the ignition switch Disconnect the PCM. Check continuity of the HO2S 1 signal circuit and the HO2S 1 low circuit between the PCM harness connector and the HO2S 1 harness connector. If the HO2S 1 signal circuit or the HO2S 1 low circuit circuit measures over 5 ohms, repair open or poor connection as necessary. Refer to Heated Oxygen Sensor (O2S) Repair in Electrical Diagnosis. Was a problem found?	--	Go to Step 13	Go to Step 10
8	Check for a poor HO2S 1 signal or HO2S low circuit terminal connection at the HO2S 1 harness connector. If a problem is found, replace terminal(s) as necessary. Refer to Heated Oxygen Sensor (O2S) Repair in Electrical Diagnosis. Was a problem found?	--	Go to Step 13	Go to Step 11
9	Check for poor HO2S 1 low circuit terminal connection at the PCM. If a problem is found, replace terminal as necessary. Refer to Heated Oxygen Sensor (O2S) Repair in Electrical Diagnosis. Was a problem found?	--	Go to Step 13	Go to Step 12
10	Check the HO2S 1 signal circuit and the HO2S low circuit for a poor terminal connection at the PCM. If a problem is found, replace terminal(s) as necessary. Refer to Heated Oxygen Sensor (O2S) Repair in Electrical Diagnosis. Was a problem found?	--	Go to Step 13	Go to Step 12
11	Replace HO2S 1. Refer to Heated Oxygen Sensor Replacement Is action complete?	--	Go to Step 13	--
12	Replace the PCM. Important:: The replacement PCM must be programmed. Refer to Powertrain Control Module Replacement/Programming	--	Go to Step 13	--
13	Turn ON the ignition switch. Review and record scan tool Fail Records data. Clear DTCs. Operate the vehicle within Fail Records conditions as noted. Using a scan tool, monitor Specific DTC info for DTC P0134 until the DTC P0134 test runs. Does the scan tool indicate DTC failed this ign?	--	Go to Step 2	System OK