GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Buick 🢒 2000 🢒 Regal 🢒 Engine 🢒 Engine Electrical 🢒 Ignition and Key Alarm Switch Assembly - Assemble - Off Vehicle

Ignition and Key Alarm Switch Assembly - Assemble - Off Vehicle Floor Shift


    Object Number: 306272 Size: SH
  1. Install the ignition and key alarm switch assembly (1) onto the electronic lock module assembly.

    2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  2. Screw the 2 tapping screws (2) into the ignition and key alarm switch assembly (1).

    3. Tighten
    Tighten the 2 tapping screws to 1.5 N·m (13 lb in).


    Object Number: 306267 Size: SH
  3. Install the key alarm connector (1) into the electronic lock module assembly (2).
    4. 3.1. Push the key alarm connector (1) into the electronic lock module assembly (2).
    3.2. Rotate the key alarm connector (1) 90 degrees so that the key alarm connector (1) locks into place.

    Object Number: 368489 Size: SH
  4. Install the electric park lock (2) onto the electronic lock module assembly (1).

    5. Object Number: 368484 Size: SH
  5. Screw the TORX® head screw (1) into the electric park lock (3).

    6. Tighten
    Tighten the TORX® head screw to 1.5 N·m (13 lb in).

  6. Reconnect the connector (2) into the electric park lock (3).

    7. Object Number: 306234 Size: SH
  7. Slide the 2 connectors (2) of the turn signal and multifunction switch assembly into the bulkhead connector (1).

    8. Object Number: 322946 Size: SH
  8. Attach the wire harness strap (2) to the wire harness assembly (1) and the steering column.
  9. Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .

Ignition and Key Alarm Switch Assembly - Assemble - Off Vehicle Column Shift


    Object Number: 306272 Size: SH
  1. Install the ignition and key alarm switch assembly (1) onto the electronic lock module assembly.

    2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  2. Screw the 2 tapping screws (2) into the ignition and key alarm switch assembly (1).

    3. Tighten
    Tighten the 2 tapping screws to 1.5 N·m (13 lb in).


    Object Number: 306267 Size: SH
  3. Install the key alarm connector (1) into the electronic lock module assembly (2).
    4. 3.1. Push the key alarm connector (1) into the electronic lock module assembly (2).
    3.2. Rotate the key alarm connector (1) 90 degrees so that the key alarm connector (1) locks into place.

    Object Number: 306234 Size: SH
  4. Slide the 2 (2) connectors of the turn signal and multifunction switch assembly into the bulkhead connector (1).

    5. Object Number: 322946 Size: SH
  5. Attach the wire harness strap (2) to the wire harness assembly (1) and the steering column.
  6. Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .