Circuit Description
The body control module (BCM) controls the retained accessory power (RAP) feature. The RAP feature allows the following components to operate for 10 minutes (or until a vehicle door opens) after the ignition switch turns from RUN or ACC to LOCK:
| • | The radio |
| • | The power windows |
| • | The power sunroof, if equipped |
The BCM interfaces with the vehicle's power distribution system through the RAP relay. The RAP relay allows the BCM to control the application of power to the RAP controlled feed circuit. When the ignition switch is in either the ACC or theRUN position, the BCM energizes the RAP relay by grounding the RAP relay control circuit.
The BCM turns off the RAP relay when the ignition switch is in the START position. The RAP feature therefore disables during engine cranking.
When the ignition switch turns from RUN to LOCK or OFF with all of the vehicle doors closed, the BCM leaves the RAP relay energized for 10 minutes, or until any vehicle door opens (the BCM detects a ground signal in one of the door ajar circuits).
Conditions for Running the DTC
The BCM must be commanding the RAP relay to energize.
Conditions for Setting the DTC
| • | The BCM detects a short to battery or open in the RAP relay control circuit when the BCM is trying to energize the RAP relay. |
| • | The condition above must be present for more than 0.3 seconds. |
Action Taken When the DTC Sets
The BCM stores DTC B1478 in memory.
Conditions for Clearing the DTC
| • | A current DTC B1478 will clear if the short to battery or open in the RAP relay control circuit is no longer detected by the BCM when the RAP relay is commanded to energize. |
| • | A history DTC B1478 will clear after 100 consecutive ignition cycles if the condition for the malfunction is no longer present. |
| • | A scan tool may be used in order to clear the DTC. |
Diagnostic Aids
| • | If the DTC B1478 is a history DTC, the fault may be intermittent. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. |
| • | The following conditions may cause an intermittent malfunction to occur: |
| - | An intermittent short to battery or open in the RAP relay control circuit |
| - | The RAP relay coil is intermittently shorted to battery or open internally. |
| - | The BCM is intermittently shorted to battery or open internally. |
Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
-
Listen for an audible click when the RAP relay operates. Command both the ON and OFF states. Repeat the commands as necessary.
-
Tests for voltage at the coil side of the RAP Relay. The INADV POWER BUS fuse supplies power to the coil side of the RAP relay.
-
This step verifies that the body control module (BCM) is providing ground to the RAP relay.
-
This step tests if ground is constantly being applied to the RAP relay.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Retained Accessory Power (RAP) Diagnostic System Check? | -- | Go to Step 2 | |
Does the RAP relay turn ON and OFF with each command? | -- | Go to Diagnostic Aids | Go to Step 3 | |
Does the test lamp illuminate? | -- | Go to Step 4 | Go to Step 10 | |
Does the test lamp turn ON and OFF with each command? | -- | Go to Step 8 | Go to Step 5 | |
Does the test lamp remain illuminated with each command? | -- | Go to Step 7 | Go to Step 6 | |
6 | Test the control circuit of the RAP relay for a short to voltage or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 9 |
7 | Test the control circuit of the RAP relay for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 9 |
8 | Inspect for poor connections at the RAP relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 11 |
9 | Inspect for poor connections at the harness connector of the body control module (BCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 12 |
10 | Repair the coil side feed circuit of the RAP relay. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 13 | -- |
11 | Replace the RAP relay. Did you complete the repair? | -- | Go to Step 13 | -- |
12 |
Did you complete the repair? | -- | Go to Step 13 | -- |
13 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
