Generator Replacement 3.1L

Important: The Delphi CS130D generator is serviced as a complete unit only.

1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection .
2. Remove the engine compartment cross vehicle brace. Refer to Cross Vehicle Brace Replacement in Body Front End.
3. Remove the drive belt from the generator. Refer to Drive Belt Replacement in Engine Mechanical-3.1L.
4. Place the coolant recovery reservoir aside for access. Refer to Coolant Recovery Reservoir Replacement in Engine Cooling.



5. Remove the bolts (1,2,3) from the generator.
6. Disconnect the electrical connector from the generator.
7. Position aside the protective boot from the generator output BAT terminal.
8. Remove the generator output BAT terminal nut and remove the positive lead from the generator.
9. Remove the generator.

1. Position the generator to the engine.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the positive lead and the generator output BAT terminal nut.

Tighten
Tighten the generator output BAT terminal nut to 20 N·m (15 lb ft).

3. Press the protective boot on to the generator output BAT terminal.
4. Install the electrical connector to the generator.



5. Install the generator bolt (2) and generator bolt (3) through the holes on the generator and finger start the bolts. Do not tighten the bolts.
6. Install the generator pivot bolt (1) through the generator and finger start the bolts finger start the bolt. Do not tighten the bolt.
7. Tighten the generator bolts in the order described. The following is a mandatory torque sequence:

Tighten

1. Tighten the generator pivot bolt (1) to 50 N·m (37 lb ft).
2. Tighten the generator bolt (2) to 50 N·m (37 lb ft).
3. Tighten the generator bolt (3) to 50 N·m (37 lb ft).
8. Install the coolant recovery reservoir . Refer to Coolant Recovery Reservoir Replacement in Engine Cooling.
9. Install the drive belt. Refer to Drive Belt Replacement in Engine Mechanical-3.1L.
10. Install the engine compartment cross brace. Refer to Cross Vehicle Brace Replacement in Body Front End.
11. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection .

Generator Replacement 3.8L

Important: The Delphi CS130D generator is serviced as a complete unit only.

1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection .
2. Remove the drive belt from the generator. Refer to Drive Belt Replacement in Engine Mechanical - 3.8L.
3. Remove the generator rear brace. Refer to Generator Brace Replacement .



4. Remove the bolts (1, 3) and stud (2) from the generator.
5. Disconnect the electrical connector from the generator.
6. Position aside the protective boot from the generator output BAT terminal for access.
7. Remove the generator output BAT terminal nut and remove the positive lead from the generator.
8. Remove the generator.

1. Position the generator to the engine.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the positive lead and the generator output BAT terminal nut.

Tighten
Tighten the generator output BAT terminal nut to 20 N·m (15 lb ft).

3. Press the protective boot on to the generator output BAT terminal.
4. Install the electrical connector to the generator.
5. Finger start the generator stud (2) to the generator bracket. Do not tighten the bolt.
6. Finger start the generator bolts (1,3) to the generator bracket. Do not tighten the bolt.
7. Tighten the generator bolts in the order described. The following is a mandatory torque sequence:

Tighten

1. Tighten the generator bolt (1) to 50 N·m (37 lb ft).
2. Tighten the generator stud (2) to 50 N·m (37 lb ft).
3. Tighten the generator rear bracket bolt (3) to 50 N·m (37 lb ft).
8. Install the generator rear brace. Refer to Generator Brace Replacement .
9. Install the drive belt from the generator. Refer to Drive Belt Replacement in Engine Mechanical - 3.8L.
10. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection .