The camshaft position (CMP) actuator is attached to each camshaft and is hydraulically operated in order to change the angle of the camshaft relative to crankshaft position (CKP). The CMP actuator solenoid is controlled by the control module. The control module sends a pulse width modulated 12V signal to a CMP actuator solenoid. The solenoid controls the amount of engine oil flow to a CMP actuator. The CMP actuator can change the camshaft angle a maximum of 25 degrees. The control module increases the pulse width to accomplish the desired camshaft operation.

The engine is running.

DTCs P0011 and P0014 are Type B DTCs.

DTCs P0011 and P0014 are Type B DTCs.

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Camshaft Actuator System Description

Electrical Information Reference

Scan Tool Reference

Control Module References for scan tool information

1. Ensure the vehicle has the proper oil viscosity.
2. Observe the engine oil level. The engine oil level should be within the operating range.
3. Allow the engine to reach operating temperature.
4. Increase the engine speed to 1,500 RPM.
5. Command each CMP actuator to 25 percent. The CMP actuator angle desired parameter should match the CMP actuator actual parameter.
6. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

1. Ignition OFF, disconnect the harness connector at the Q6 CMP actuator solenoid.
2. With the ignition ON, measure for battery voltage between the CMP actuator solenoid control of the affected actuator and a ground.

⇒	If less than battery voltage, test the CMP actuator control circuit for an open, short to ground. If the circuit tests normal, replace the K20 ECM.

3. Connect a test lamp between the CMP actuator solenoid control of the affected actuator and a good ground. The test lamp should not illuminate.

⇒	If the test lamp illuminates, test the CMP actuator control circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

4. Command each CMP actuator solenoid between 0-50 percent. The test lamp should turn ON and OFF.

⇒	If the test lamp does not turn ON and OFF, test the CMP actuator control circuit for high resistance. If the circuit tests normal, replace the K20 ECM.

5. Connect a test lamp between the low reference circuit of the CMP actuator solenoid of the affected actuator and battery voltage. The test lamp should illuminate.

⇒	If the test lamp does not illuminate, test the low reference circuit for an open, high resistance. If the circuit tests normal, replace the K20 ECM.

6. Determine that the vehicle has the correct engine oil. Refer to Service and Appearance Care in the owner's manual.

⇒	If the engine oil life system monitor displays the Change Oil Soon message, the engine oil is more than one year old, contains additives, or is not the correct viscosity, change the oil.

7. Test the engine oil pressure. Refer to Oil Pressure Diagnosis and Testing.

⇒	If the oil pressure is low, correct the low pressure first.

8. Inspect each CMP actuator solenoid valve assembly for the following:

•	Torn screens

•	Debris on the screens

•	Debris clogging the oil ports

•	Missing screens

•	Oil seepage at the solenoid connector pins

9. Inspect for the following conditions:

•	Excessive timing chain play

•	Proper installation of the CMP actuator assembly

1. Measure the resistance of each CMP actuator solenoid valve assembly. Resistance should be between 8-12Ω.
2. Connect a jumper wire between the CMP actuator low reference circuit at the solenoid and a good ground. Connect a fused jumper wire to the CMP actuator high control circuit at the solenoid. Momentarily touch the fused jumper to B+. Observe the spool valve inside the CMP actuator. The spool valve should move from fully closed to fully opened position.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.