GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC B370A 39: Rain Sensor Internal Malfunction

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Rain Sensor B+

1

1

--

--

Rain Sensor Ground

--

1

1

--

Rain Sensor Signal

B370A 39

B370A 39

B370A 39

B370A 39

1. Windshield Outside Moisture Sensor Malfunction

Circuit/System Description

B+ voltage is supplied to the windshield outside moisture sensor. Whenever the ignition is ON, or in accessory positions, the body control module (BCM), sends the turn signal / multifunction switch status by using a pulse width modulated (PWM) signal. When a wipe cycle is needed, the windshield outside moisture sensor sends a PWM voltage signal to the BCM, initiating the wiper operation. The BCM commands the windshield wiper motor wipe cycles. If a fault occurs at any time between the windshield outside moisture sensor and BCM, the BCM will use the inputs from the turn signal / multifunction switch in the delay positions to operate the windshield wiper motor at continuous variable delay intervals.

Conditions for Running the DTC

    • Ignition ON.
    •  The system voltage is between 9 V and 16 V.

Conditions for Setting the DTC

The BCM receives an invalid signal from the windshield outside moisture sensor.

Action Taken When the DTC Sets

    • If the BCM loses communication with the windshield outside moisture sensor while the windshield outside moisture sensor was requesting single wipes, it shall fail soft the wipers operation to front wiper manual - intermittent with a fixed dwell time of 4 seconds.
    • If the BCM loses communication with the windshield outside moisture sensor while the windshield outside moisture sensor was continuously requesting low, it shall fail soft the wipers operation to front wiper manual - low.
    • If the BCM loses communication with the windshield outside moisture sensor while the windshield outside moisture sensor was continuously requesting high, it shall fail soft the wipers operation to front wiper manual - high.

Conditions for Clearing the DTC

A current DTC clears when the diagnostic runs and passes.

Reference Information

Schematic Reference

Wiper/Washer Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Wiper/Washer System Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for diagnostic tester information

Circuit/System Verification

Ignition ON, S78 Turn Signal/Multifunction Switch in the low position. The windshield wipers should operate at low speed.

If the windshield wipers do not operate, refer to Windshield Wiper System Malfunction.

Circuit/System Testing

  1. Ignition OFF, disconnect the harness connector at the B117 Windshield Outside Moisture Sensor.
  2. Test for less than 5 Ω between the ground circuit terminal 2 and ground.
  3. If greater than the specified value, test the ground circuit for an open / high resistance.
  4. Ignition ON, verify that a test lamp illuminates between B+ voltage circuit terminal 1 and ground.
  5. If the test lamp does not illuminate, test the B+ voltage circuit for a short to ground or an open/high resistance.
  6. Ignition ON, test for 4-10 V between the signal circuit terminal 3 and ground.
  7. If less than the specified range, test the signal circuit for an open/high resistance. If the circuit tests normal, replace the K9 Body Control Module (BCM).
  8. If all circuits test normal, replace the B117 Windshield Outside Moisture Sensor.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    • LINK
    •  Control Module References for BCM replacement, setup, and programming