Diagnostic Instructions

DTC Descriptor

DTC B0967 02: Parking Aid On/Off Switch Circuit Short To Ground

DTC B0968 01: Parking Aid On/Off Switch Indicator Circuit Short To Battery

DTC B0968 06: Parking Aid On/Off Switch Indicator Circuit Low Voltage/Open

Diagnostic Fault Information

Circuit	Short to Ground	Open/High Resistance	Short to Voltage	Signal Performance
Parking Assist Switch Signal	B0967 02	1	--	--
Parking Assist Switch Indicator Control	B0968 06	B0968 06	B0968 01	--
Parking Assist Switch Ground	--	B0968 06	--	--
1. Parking Assist Switch Malfunction

Circuit/System Description

The parking assist can be activated/deactivated by pressing the parking assist switch. By engaging the reverse gear the parking assist can also be activated. By subsequently pressing the parking assist switch the parking assist can be disabled again.

The indicator in the parking assist switch shows the status of the parking assist. If the lamp is ON, the parking assist is activated.

Conditions for Running the DTC

Conditions for Setting the DTC

B0967 02

The object alarm module has detected a short to ground.

B0968 01

The object alarm module has detected a short to battery.

B0968 06

The object alarm module has detected a short to ground or open.

Action Taken When the DTC Sets

Conditions for Clearing the DTC

The condition for setting the DTC is no longer present.

Reference Information

Schematic Reference

Object Detection Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Object Detection Description and Operation

Electrical Information Reference

Scan Tool Reference

Control Module References

Circuit/System Verification

1. Verify that DTC B0967 02 is not present.

⇒	If DTC is present, refer to Parking Assist Switch Malfunction.

2. Verify that B0968 01 or B0968 06 is not present.

⇒	If DTC is present, refer to Parking Assist Switch Indicator Malfunction.

3. Activate and deactivate the parking assist switch and verify the scan tool Park Assist Switch parameter changes between Active and Inactive.

Circuit/System Testing

Parking Assist Switch Malfunction

1. Ignition OFF, disconnect the X3 harness connector at the K41 Object Alarm Module.
2. Test for infinite resistance between the input signal circuit terminal 8 (X3) at the K41 Object Alarm Module harness connector and ground.

⇒	If less than the specified range, test input signal circuit for a short to ground. If the circuit tests normal, replace the S48D Multifunction Switch - I/P 2.

3. If all circuits test normal, replace the K41 Object Alarm Module.

Parking Assist Switch Indicator Malfunction

1. Ignition OFF, disconnect the X3 harness connector at the K41 Object Alarm Module and the X1 harness connector at the S48D Multifunction Switch - I/P 2.
2. Test for less than 5 Ω between the S48D Multifunction Switch - I/P 2 ground circuit terminal 2 (X1) and ground.

⇒	If greater than the specified range, test the ground circuit for an open/high resistance.

3. Ignition ON, test for less than 0.3 V between the control circuit terminal 3 (X3) at the K41 Object Alarm Module harness connector and ground.

⇒	If greater than the specified range, test the control circuit for a short to voltage.

4. Ignition OFF, test for infinite resistance between the control circuit terminal 3 (X3) at the K41 Object Alarm Module harness connector and ground.

⇒	If less than the specified range, test control circuit for a short to ground.

5. Test for less than 5 Ω between the S48D Multifunction Switch - I/P 2 control circuit terminal 6 (X1) and the control circuit terminal 3 (X3) at the K41 Object Alarm Module harness connector

⇒	If greater than the specified range, test the control circuit for an open/high resistance.

6. If all circuits test normal, connect the X3 harness connector to the K41 Object Alarm Module, replace the S48D Multifunction Switch - I/P 2 and verify the DTC does not reset.

⇒	If the DTC resets, replace the K41 Object Alarm Module.

Repair Instructions

Perform the Diagnostic Repair Verification