GM Service Manual Online
For 1990-2009 cars only

Object Number: 517311  Size: SF
Engine Controls Components
IAC, Oil Level Switch and Oil Pressure Indicator
OBD II Symbol Description Notice
Handling ESD Sensitive Parts Notice

Circuit Description

The Powertrain Control Module (PCM) controls engine idle speed by adjusting the position of the idle air control (IAC) motor pintle. The IAC is a bi-directional motor driven by two coils. The PCM applies current to the IAC coils in pulses (counts) to extend the IAC pintle into a passage in the throttle body to decrease air flow. The PCM reverses the current to retract the pintle, increasing air flow. This method allows highly accurate control of idle speed and quick response to changes in engine load. If the PCM detects a condition where too high of an idle speed is present and the PCM is unable to adjust idle speed by increasing the IAC counts, DTC P0507 will set.

Conditions for Running the DTC

    •  No active TP, ECT, MAP, IAT, MAF, CKP sensor, EVAP, misfire, EGR, VSS, fuel trim, injector circuit, DTCs active
    •  The ECT is above 70°C (158°F).
    •  The engine has been running for at least 2 minutes.
    •  The system voltage is between 9.0-16.0 volts.
    •  The vehicle speed is less than 4.8 km/h (3 mph).
    •  The IAT is above -18°C (0°F).
    •  The throttle is closed.
    •  BARO is above 65 kPa.

Conditions for Setting the DTC

    • The IAC valve reads less than 15 counts on the scan tool.
    • The Engine Speed is more than 175 RPM higher than Desired Idle.

Action Taken When the DTC Sets

    • The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test has been run and failed.
    • The PCM will store conditions which were present when the DTC set as Freeze Frame/Failure Records data.

Conditions for Clearing the MIL/DTC

    • The PCM will turn OFF the malfunction indicator lamp (MIL) during the third consecutive trip in which the diagnostic has run and passed.
    • The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
    • The DTC can be cleared by using a scan tool.

Diagnostic Aids

Inspect for the following conditions:

    •  Poor connection at the PCM or IAC valve--Inspect harness connectors for:
       - Backed out terminals
       - Improper mating
       - Broken locks
       - Improperly formed or damaged terminals
       - Poor terminal to wire connection
    •  Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
    •  Damaged harness--Inspect the wiring harness for damage. Refer to Wiring Repairs in Wiring Systems.
    •  Restricted air intake system--Inspect for a possible collapsed air intake duct, restricted air filter element, or foreign objects blocking the air intake system.
    •  Throttle body--Inspect for objects blocking the IAC passage or throttle bore, excessive deposits in the IAC passage, on the IAC pintle, in the throttle bore and on the throttle plate.
    •  Large vacuum leak--Inspect for a condition that causes a large vacuum leak, such as a incorrectly installed or faulty PCV valve or the brake booster hose disconnected. Refer to Symptoms .

If the DTC cannot be duplicated and is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set. Also refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This vehicle is equipped with a PCM which utilizes an electrically erasable programmable read only memory (EEPROM). When the PCM is being replaced, the new PCM must be programmed.

Step

Action

Values

Yes

No

1

Did you perform the Powertrain On-Board Diagnostic (OBD) System Check?

--

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

2

Are any other DTCs set?

--

Go to the applicable DTC table

Go to Step 3

3

  1. Start the engine.
  2. Turn OFF all accessories.
  3. Using a scan tool, command the RPM up to 1500, down to 650, and then up to 1500 while monitoring the Engine Speed on the scan tool.

Does the Engine Speed remain within the specified value of Desired Idle for each RPM commanded

±50 RPM

Go to Diagnostic Aids

Go to Step 4

4

  1. Disconnect the IAC.
  2. Install J 37027-A IAC System Motor Analyzer to IAC harness connector.
  3. Start the engine, with a scan tool command the RPM up to 1500, down to 650, and then up to 1500 while observing the node lamp.

Does the node lamp cycle from red to green (never off)?

--

Go to Step 6

Go to Step 5

5

  1. Test the following circuits for an open, short to voltage, or a short to ground:
  2. • IAC A Low
    • IAC A High
    • IAC B Low
    • IAC B High
  3. If a problem is found, repair as necessary. Refer to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 11

Go to Step 9

6

  1. Visually/physically inspect for the following conditions:
  2. •  Vacuum leaks
    •  Throttle body tampering--Throttle Lever Stop Screw turned
    •  Throttle plate or throttle shaft for binding
    •  Faulty, missing, or incorrectly installed PCV valve
  3. If a problem is found repair as necessary.

Did you find and correct any conditions?

--

Go to appropriate section for on vehicle service

Go to Step 7

7

  1. Inspect for a poor connection at the IAC harness connector.
  2. If a problem is found repair as necessary. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 11

Go to Step 8

8

Replace the IAC valve. Refer to Idle Air Control Valve Replacement .

Did you complete the replacement?

--

Go to Step 11

--

9

  1. Inspect for a poor connection at the PCM harness connector.
  2. If a problem is found repair as necessary. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 11

Go to Step 10

10

Important: : The replacement PCM must be programmed.

Replace the PCM. Refer to Powertrain Control Module Replacement/Programming .

Did you complete the replacement?

--

Go to Step 11

--

11

  1. Start the engine.
  2. Turn OFF all the accessories.
  3. Using a scan tool, command the RPM up to 1500, down to 650, and then up to 1500 while monitoring the Engine Speed on the scan tool.

Does the Engine Speed remain within the specified value of Desired Idle for each RPM commanded?

±50 RPM

System OK

Go to Step 2