The powertrain control module (PCM) output (L) terminal to the alternator determines when the alternator will be turned off. It is on under all normal vehicle operating conditions except during low RPM conditions. The alternator is turned off during low RPM conditions to remove excess load from the engine.
The PCM input field (F) terminal from the alternator provides a 400 Hz PWM signal to the PCM. The duty cycle of the F terminal mimics the duty cycle of the field coils in the alternator, Thus, the F terminal duty cycle indicates the relative electrical load on the alternator.
The alternator telltale lamp will illuminate any time the ignition is ON and engine is not running. The telltale will go out after the engine is running and the alternator is putting out the desired amperage.
OR
OR
OR
The PCM stores conditions which were present when the DTC set as Failure Records only. This information will not be stored as Freeze Frame Records.
• | The DTC becomes history when the conditions for setting the DTC are no longer present. |
• | The history DTC clears after 40 malfunction free warm-up cycles. |
• | The PCM receives a clear code command from the scan tool. |
Inspect for the following conditions:
• | Poor connection at the PCM or Generator--Inspect the harness connectors for: |
- | Backed out terminals |
- | Improper mating |
- | Broken locks |
- | Improperly formed or damaged terminals |
- | Poor terminal to wire connection |
• | Refer to Testing for Intermittent Conditions and Poor Connections and Wiring Repairs in Wiring Systems. |
• | Damaged harness--Inspect the wiring harness for damage. If the harness appears to be OK, disconnect the PCM, turn the ignition on and observe the voltmeter connected to the generator circuits at the PCM harness connector while moving connectors and wiring harnesses related to the generator control circuit. A change in voltage will indicate the location of the fault. Refer to Testing for Intermittent Conditions and Poor Connections and Wiring Repairs in Wiring Systems. |
The numbers below refer to the step numbers on the diagnostic table.
Step | Action | Values | Yes | No |
---|---|---|---|---|
1 | Did you perform the Powertrain On Board Diagnostic (OBD) System Check? | -- | ||
2 | Using the scan tool, monitor Generator PWM. Does the scan tool indicate that the Generator PWM is within the indicated range? | 5% - 95% | Go to Diagnostic System Check - Engine Electrical in Engine Electrical. | |
3 |
Command the Generator ON with the scan tool while monitoring the DMM. Does the voltage change from the first indicated value to the second indicated value? | 0.0V 5.0V | ||
4 |
Is the Generator PWM display affected? | -- | Go to Diagnostic System Check - Engine Electrical in Engine Electrical. | |
5 | Test the (L) circuit for an open or short to ground and repair if necessary. Refer to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||
6 | Test the (L) circuit for a short to voltage and repair if necessary. Refer to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||
7 | Test the (F) circuit for an open or short to ground and repair if necessary. Refer to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||
8 | Test the (F) circuit for a short to voltage and repair if necessary. Refer to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||
9 | Test for a poor connection at the PCM and repair if necessary. Refer to Testing for Continuity and Testing for Intermittent Conditions and Poor Connections in Wiring Systems. Did you find and correct the condition? | -- | ||
Important: : The replacement PCM must be programmed. Replace the PCM. Refer to Powertrain Control Module Replacement/Programming . Is the action complete? | -- | -- | ||
11 |
Does the scan tool indicate DTC P0620 failed this ignition? | -- | System OK |