GM Service Manual Online
For 1990-2009 cars only

Tools Required

J 41396 Park Lock Cable Pliers


    Object Number: 324902  Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

    Important: Lubricate all moving parts of the linear shift assembly with synthetic grease.

  1. Install the gearshift lever assembly support bracket and secure by using 3 flat head 6 lobed socket tap screws.
  2. Tighten
    Tighten the flat head 6 lobed socket tap screws to 10 N·m (89 lb in).


    Object Number: 324900  Size: SH
  3. Insert the cam bushing (2) into the cable shift cam assembly.
  4. Install the cable shift cam assembly (1).
  5. Install the hexagon flange head bolt.
  6. Tighten
    Tighten the hexagon flange head bolt to 18 N·m (14 lb ft).


    Object Number: 324897  Size: SH
  7. Install the park lock cable assembly.
  8. Install the 2 oval head 6 lobed socket tap screws to the gearshift lever assembly support bracket.
  9. Tighten
    Tighten the oval head 6 lobed socket tap screws to 6.5 N·m (58 lb in).


    Object Number: 324909  Size: SH
  10. Install the shift lever clevis (1).
  11. Install the ball actuator assembly (2).
  12. Install the hexagon flanged head bolt.
  13. Tighten
    Tighten the hexagon flanged head bolt to 18 N·m (14 lb ft).


    Object Number: 324874  Size: SH
  14. Connect the park lock cable assembly (1) into the lock module assembly.
  15. • The lock cylinder should be in the off-lock position.
    • The locking tab at the end of the park lock cable assembly (1) must be installed into the lock module assembly.

    Object Number: 324884  Size: SH
  16. Adjust the park lock cable assembly using the following steps:
  17. 11.1. Use the gear shift lever to put the column in the park position.
    11.2. Put the ignition switch in the off-lock position. Remove the key.
    11.3. Unlock the adjuster ring (1) on the park lock cable assembly with J 41396 .
    11.4. Pull on the cable until the park lock latch contacts the gear shift lever. Release the cable.
    11.5. Lock the adjuster ring (1) securely in place on the park lock cable assembly with J 41396 .
  18. Inspect the park lock cable assembly using the following steps:
  19. 12.1. Put the lock cylinder in the off-lock position. The gear shift lever should not be able to shift out of the park position.
    12.2. Turn the key to the run position and put the gear shift lever in the neutral position.
    12.3. With the gear shift lever in the neutral position the lock cylinder should not be able to go into the off-lock position.
    12.4. Put the gear shift lever in the park position.
    12.5. Put the lock cylinder in the off-lock position and then remove the key.

    Object Number: 324906  Size: SH
  20. Install the automatic transmission shift lock control.
  21. Install the gear shift lever and put the column in the neutral position.


    Object Number: 324912  Size: SH
  22. Adjust the automatic transmission shift lock control using the following steps:
  23. 14.1. Pull the tab (1) out on the block (2) side of the automatic transmission shift lock control.
    14.2. Press on the adjuster block (2) to compress the internal adjuster spring to disengage the adjuster teeth. Slide the adjuster block (2) as far away from the solenoid as possible.
    14.3. Lock in place by pushing the tab (1) back in.
  24. Inspect the automatic transmission shift lock control using the following steps:
  25. 15.1. The automatic transmission shift lock control must lock the gear shift lever when it is put into the park position.
    15.2. When the column is installed in the vehicle you will not be able to shift the gear shift lever out of the park position without pressing on the brake pedal. The solenoid will be energized.
    15.3. Readjust if needed.
  26. Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .