Was the Door Locks System Check performed?

--

Go to Step 2

Go to Power Door Locks System Check

Did you perform the BCM Diagnostic System Check?

--

Go to Step 3

Go to Diagnostic System Check - Body Control System

Is the door lock actuator of the driver door inoperative?

--

Go to Step 4

Go to Step 5

1. Disconnect the driver's side door lock actuator motor electrical connector C2.
2. Connect a test light between the driver's side door lock actuator motor harness connector C2 terminals A and B.
3. Momentarily press unlock on either door lock switch while observing the test light.

Does the test light flash once?

--

Go to Step 8

Go to Step 9

Are all the passenger doors inoperative?

--

Go to Step 6

Go to Step 7

Use a test light in order to probe between B+ and the BCM connector C3 terminal H.

Is the test light on?

--

Go to Step 18

Go to Step 19

1. Turn the ignition switch to the LOCK position.
2. Disconnect the electrical connector C2 of the inoperative door lock actuator motor.
3. Use a test light in order to connect between the inoperative door lock actuator motor harness connector C2 terminals A and B.
4. While observing the test light, press lock on either door lock switch.

Does the test light flash once while pressing lock?

--

Go to Step 21

Go to Step 22

Replace the driver's side door lock actuator motor.

Is the repair complete?

--

Go to Step 17

--

Connect a test light between B+ and the drivers side door lock actuator motor harness connector terminal B.

Does the test light illuminate?

--

Go to Step 10

Go to Step 11

Connect a test light between B+ and the drivers side door lock actuator motor harness connector terminal A.

Does the test light illuminate?

--

Go to Step 12

Go to Step 13

Repair a poor connection or an open in circuit 295.

Is the repair complete?

--

Go to Step 17

--

Replace the door lock relay.

Is the repair complete?

--

Go to Step 17

--

Connect a test light between B+ and the door lock relay terminal B2.

Does the test light illuminate?

--

Go to Step 14

Go to Step 15

1. Disconnect the door lock relay.
2. Connect a digital multimeter (DMM).
3. Test for continuity between the door lock relay terminal C1 (relay side) and the actuator connector C2 terminal A.

Is there continuity?

--

Go to Step 12

Go to Step 16

Repair a poor connection or an open in circuit 1450.

Is the repair complete?

--

Go to Step 17

--

Repair a poor connection or an open in circuit 694.

Is the repair complete?

--

Go to Step 17

--

1. Turn the ignition switch to the LOCK position.
2. Reconnect all of the connectors.
3. Reinstall any components that were removed.

Have all repairs been made?

--

Go to Power Door Locks System Check

--

1. Use a test light in order to connect by probing between the BCM connector C3 terminal H and ground.
2. While observing the test light, press unlock momentarily on either door lock switch.

While pressing unlock, does the test light flash?

--

Go to Step 20

Go to Step 19

1. Replace the BCM. Refer to Body Control Module Replacement in Body Control System.
2. Perform the Setup New BCM procedure. Refer to Body Control Module (BCM) Programming/RPO Configuration in Body Control System.

Is the repair complete?

--

Go to Step 17

--

Repair a poor connection or an open in circuit 294.

Is the repair complete?

--

Go to Step 17

--

Replace the door lock. Refer to Front Side Door Lock Replacement or Rear Door Lock Replacement .

Is the repair complete?

--

Go to Step 17

--

1. Use a test light in order to connect between the inoperative door lock actuator motor harness connector C2 terminal A and ground.
2. While observing the test light, press unlock on either door lock switch.

Does the test light flash once while pressing unlock?

--

Go to Step 23

Go to Step 24

Repair a poor connection or an open in circuit 295.

Is the repair complete?

--

Go to Step 17

--

Repair a poor connection or an open in circuit 294.

Is the repair complete?

--

Go to Step 17

--