Circuit Description
The circuit uses two different types of crankshaft position (CKP) sensors. The 7x CKP sensor is connected directly to the ignition control (IC) module, and consists of the following circuits:
| • | The CKP 1 sensor signal circuit. |
| • | The low reference circuit. |
The 24x CKP sensor connects directly to the powertrain control (PCM) module, and consists of the following circuits:
| • | The 12-volt reference circuit. |
| • | The medium resolution engine speed signal circuit. |
| • | The low reference circuit. |
Conditions for Running the DTC
The engine is running, 3X reference pulses are being received, for a minimum of 3 seconds.
Conditions for Setting the DTC
The ratio of 24X reference pulses to 3X reference pulses received by the PCM is incorrect.
Action Taken When the DTC Sets
| • | The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test has been run and failed. |
| • | The PCM will store conditions which were present when the DTC set as Freeze Frame/Failure Records data. |
Conditions for Clearing the MIL/DTC
| • | The PCM will turn OFF the malfunction indicator lamp (MIL) during the third consecutive trip in which the diagnostic has run and passed. |
| • | The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
| • | The DTC can be cleared by using a scan tool. |
Diagnostic Aids
DTC P0336 can be caused by secondary components leaking high voltage into the ignition control (IC) module. Inspect for the following conditions:
| • | Incorrect harness routing near secondary ignition components. |
| • | Ignition coil arcing to wiring harness or IC module, inspect ignition coils for cracks, carbon tracking, or other signs of damage. |
| • | Secondary ignition wires arcing to wiring harness. |
| • | If the DTC is determined to be intermittent, refer to Intermittent Conditions |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
If sent here from DTC P0327 proceed with DTC P0336 Diagnostic even if P0336 has not failed this ignition.
-
The 24X RPM on the scan tool should change each time the Medium Resolution Engine Speed signal circuit is touched.
-
If the fuse opens in the jumper wire, there is a short to ground on the Medium Resolution Engine Speed signal circuit.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics | ||||
1 | Did you perform the Diagnostic System Check-Engine Controls? | -- | Go to Step 2 | |
Does 24X RPM vary with engine speed up to approximately 1600 RPM? | -- | Go to Step 3 | Go to Step 4 | |
3 |
Does the DTC fail this ignition? | -- | Go to Step 4 | Go to Diagnostic Aids |
4 |
Important: A short to ground on the Cam Sensor 12-Volt Reference circuit can cause DTC P0336 and DTC P0327 to set. Test this circuit for a short to ground before proceeding with this diagnostic table. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Does the voltage measure near the specified value? | B+ | Go to Step 6 | Go to Step 5 |
5 |
Did you find and correct the condition? | -- | Go to Step 16 | Go To Step 12 |
6 |
Does test lamp illuminate? | -- | Go to Step 8 | Go to Step 7 |
7 |
Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 12 |
Does 24X RPM change EACH time the signal circuit is touched? | -- | Go to Step 13 | Go to Step 9 | |
Did the fuse in the jumper wire open? | -- | Go to Step 11 | Go to Step 10 | |
10 | Test the CKP Medium Resolution Engine Speed signal circuit of the 24X CKP sensor for a short to voltage or an open. Refer to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 12 |
11 | Test the CKP Medium Resolution Engine Speed signal circuit of the 24X CKP sensor for a short to ground. Refer to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 12 |
12 | Inspect for faulty connections at the PCM. Refer to Testing for Continuity and Testing for Intermittent Conditions and Poor Connections in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 14 |
13 | Inspect for faulty connections at the 24X CKP sensor. Refer to Testing for Continuity and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 16 | Go to Step 15 |
14 | Replace the PCM. Refer to Powertrain Control Module Replacement . Did you complete the replacement? | -- | Go to Step 16 | -- |
15 | Replace 24X CKP sensor. Refer to Crankshaft Position Sensor Replacement . Did you complete the replacement? | -- | Go to Step 16 | -- |
16 |
Does the DTC run and pass? | -- | Go to Step 17 | Go to Step 2 |
17 | With a scan tool, observe the stored information in Capture Info. Does the scan tool display any DTCs that you have not diagnosed? | -- | System OK | |
