Heated oxygen sensors (HO2S) are used for fuel control and post catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content of the exhaust stream. When the vehicle is first started, the powertrain control module (PCM) operates in an Open Loop mode, ignoring the HO2S signal voltage when calculating the air-to-fuel ratio. The PCM supplies the HO2S with a reference, or bias, voltage of about 450 mV. The HO2S generates a voltage within a range of 0-1,000 mV that fluctuates above and below bias voltage once in Closed Loop. A high HO2S voltage output indicates a rich fuel mixture. A low HO2S voltage output indicates a lean mixture. Heating elements inside the HO2S minimize the time required for the sensors to reach operating temperature, and to provide an accurate voltage signal. The HO2S 2 is used for post catalyst monitoring. If the PCM detects that the HO2S 2 voltage is above a calibrated amount for an excessive amount of time, DTC P0138 will set.
The HO2S 2 has the following circuits:
• | A HO2S 2 high signal circuit |
• | A HO2S 2 low signal circuit |
• | A HO2S 2 heater ignition voltage circuit |
• | A HO2S 2 heater ground circuit |
• | DTCs P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0121, P0122, P0123, P0125, P0128, P0201-P0206, P0410, P0440, P0442, P0443, P0446, P0449, P1441 are not set. |
• | The Air Fuel Ratio parameter is between 14.5:1-14.8:1. |
• | The TP Sensor parameter is between 3-40 percent. |
• | The system voltage is between 9-18 volts. |
The PCM detects that the HO2S 2 voltage is more than 920 mV for more than 2 minutes during Closed Loop operation.
OR
The PCM detects that the HO2S 2 voltage is more than 200 mV during decel fuel cut-off (DFCO) for more than 30 seconds.
• | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
• | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
• | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
• | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
• | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
• | Clear the MIL and the DTC with a scan tool. |
Step | Action | Values | Yes | No | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Controls Connector End Views or Powertrain Control Module Connector End Views | ||||||||||||||||
1 | Did you perform the Diagnostic System Check-Engine Controls? | -- | Go to Step 2 | |||||||||||||
2 | Is DTC P0140 also set? | -- | Go to DTC P0140 | Go to Step 3 | ||||||||||||
3 |
Is the HO2S 2 voltage more than the specified value? | 920 mV | Go to Step 5 | Go to Step 4 | ||||||||||||
4 |
Did the DTC fail this ignition? | -- | Go to Step 5 | Go to Intermittent Conditions | ||||||||||||
5 |
Is the HO2S 2 voltage more than the specified value? | 920 mV | Go to Step 6 | Go to Step 7 | ||||||||||||
6 | Test the HO2S 2 high signal circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 9 | ||||||||||||
7 | Inspect for the following that may affect the HO2S operation: Notice: Refer to Silicon Contamination of Heated Oxygen Sensors Notice in the Preface section.
Notice: Refer to Heated Oxygen and Oxygen Sensor Notice in the Preface section.
Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 8 | ||||||||||||
8 | Test for an intermittent and for a poor connection at the harness connector of the HO2S 2. Refer to Testing for Intermittent Conditions and Poor Connections , Connector Repairs , and Heated Oxygen Sensor Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 10 | ||||||||||||
9 | Test for an intermittent and for a poor connection at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 11 | ||||||||||||
10 | Replace the HO2S 2. Refer to Heated Oxygen Sensor 2 Replacement . Did you complete the replacement? | -- | Go to Step 12 | -- | ||||||||||||
11 | Replace the PCM. Refer to Powertrain Control Module Replacement . Did you complete the replacement? | -- | Go to Step 12 | -- | ||||||||||||
12 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 13 | ||||||||||||
13 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | System OK |