DTC U1001-U1254. Buick Rendezvous

For 1990-2009 cars only

Makes 🢒 Buick 🢒 2003 🢒 Rendezvous - FWD 🢒 DTC 🢒 DTC U1001-U1254

Control Module	ID Number
PCM	016
EBCM	040
BCM	064
SDM	088
IPC	096
HUD	098
Radio	128
VIU	146
HVAC	152
MSM	166
Theft Deterrent Control Module	192

When more than one Loss of Communication DTC is set in either one module or in several modules, diagnose the DTCs in the following order:

Current DTCs before history DTCs unless told otherwise in the diagnostic tables.
The DTC which is reported the most times.
From the lowest number DTC to the highest number DTC.

Circuit Description

Modules connected to the class 2 serial data circuit monitor for serial data communications during normal vehicle operation. Operating information and commands are exchanged among the modules. When a module receives a message for a critical operating parameter, the module records the identification number of the module which sent the message for State of Health monitoring. A critical operating parameter is one which, when not received, requires that the module use a default value for that parameter. Once an identification number is learned by a module, it will monitor for that module's Node Alive message. Each module on the class 2 serial data circuit which is powered and performing functions that require detection of a communications malfunction is required to send a Node Alive message every 2 seconds. When no message is detected from a learned identification number for 5 seconds, a DTC U1XXX is set. The XXX is equal to the 3 digit identification number of the module.

The Control Module ID Number list provides a method for determining which module is not communicating. A module with an internal class 2 serial data circuit malfunction or which loses power during the current ignition cycle would have a Lost Communication DTC set by other modules. The modules that can communicate will set a DTC indicating the module that cannot communicate.

Conditions for Running the DTC

•	Voltage supplied to the module is in the normal operating voltage range of 9 to 16 volts.

•	Diagnostic trouble codes U1300, U1301 and U1305 do not have a current status.

•	The vehicle power mode requires serial data communication to occur.

Conditions for Setting the DTC

A message from a learned identification number has not been detected for the past 5 seconds.

Conditions for Clearing the DTC

•	A current DTC clears when the malfunction is no longer present.

•	A history DTC clears when the module ignition cycle counter reaches the reset threshold, without a repeat of the malfunction.

Test Description

The number below refers to the step number on the diagnostic table.

The module which was not communicating on the class 2 serial data circuit may have set Loss of Communication DTCs for those modules that it was monitoring.

Step

Action

Yes

Schematic Reference: Data Link Connector Schematics

Connector End View Reference: Master Electrical Component List and Inline Harness Connector End Views in Wiring Systems

Important: Use the control module ID number list in order to determine which module is not communicating.

Test the following circuits of the module that is not communicating for an open or a short to ground:

•	The battery positive voltage input circuits

•	The battery positive voltage output circuits

•	The ignition voltage input circuits

•	The ignition voltage output circuits

•	The switched battery positive voltage circuits

Refer to the following:

•	Control Module References in Body Control System for the applicable schematic

•	Circuit Testing in Wiring Systems

•	Wiring Repairs in Wiring Systems

Did you find and correct the condition?

Go to Step 6

Go to Step 2

Turn OFF the ignition.
Test the ground circuits of the module that is not communicating for an open.

Refer to the following:

•	Control Module References in Body Control System for the applicable Schematic

•	Circuit Testing in Wiring Systems

•	Wiring Repairs in Wiring Systems

Did you find and correct the condition?

Go to Step 6

Go to Step 3

Test the class 2 serial data circuits of the module that is not communicating for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 6

Go to Step 4

Inspect the harness connectors of the module that is not communicating for poor connections and terminal tension at the following circuits:

•	The battery positive voltage input circuits

•	The battery positive voltage output circuits

•	The ignition voltage input circuits

•	The ignition voltage output circuits

•	The switched battery positive voltage supply circuits

•	The ground circuits

•	The class 2 serial data circuits

Refer to the following:

•	Control Module References in Body Control System for the applicable schematic

•	Testing for Intermittent Conditions and Poor Connections in Wiring Systems

•	Connector Repairs in Wiring Systems

Did you find and correct the condition?

Go to Step 6

Go to Step 5

Important: Perform the programming or set up procedure for the module, if required.

Replace the module that is not communicating. Refer to Control Module References for the applicable replacement procedure.

Did you complete the replacement?

Go to Step 6

Install a scan tool.
Turn ON the ignition with the engine OFF.
Select the Display DTCs function for the module which was not communicating.

Does the scan tool display any DTCs which do not begin with a "U"?

Go to Control Module References for the applicable Diagnostic System Check

Go to Step 7

Select the Display DTCs function for the modules which had the Loss of Communications DTC set.

Does the scan tool display any DTCs which do not begin with a "U"?

Go to Control Module References for the applicable Diagnostic System Check

Go to Step 8

Use the scan tool in order to clear the DTCs.
Continue diagnosing or clearing the DTCs until all the modules have been diagnosed and all the DTCs have been cleared.

Did you complete the action?

Go to Control Module References for the applicable Diagnostic System Check