Discharge Hose Replacement LX9
Tools Required
J 39400-A Halogen Leak Detector
Removal Procedure
- Remove the air cleaner assembly. Refer to
Air Cleaner Assembly Replacement.
- Recover the refrigerant from the A/C system. Refer to
Refrigerant Recovery and Recharging .
- Remove the discharge hose to condenser nut.
- Disconnect the discharge hose from the condenser.
Important: Cap or tape the open A/C components immediately to prevent A/C system contamination.
- Cap or tape the discharge port on the condenser.
- Remove the lower air baffle. Refer to
Radiator Air Baffle Assemblies and Deflectors.
- Remove the discharge hose to compressor nut.
- Disconnect the discharge hose from the compressor.
- Cap or tape the compressor discharge port.
- Remove the discharge hose.
- Remove and discard the sealing washers.
Installation Procedure
- Install a new sealing washer onto the compressor side of the discharge hose. Refer to
Sealing Washer Replacement .
- Install the discharge hose.
- Remove the cap or tape from the compressor discharge port.
- Connect the discharge hose to the compressor.
Notice: Refer to Fastener Notice in the Preface section.
- Install the discharge hose to compressor nut.
Tighten
Tighten the nut to 16 N·m (12 lb ft).
- Install the lower air baffle. Refer to
Radiator Air Baffle Assemblies and Deflectors.
- Lower the vehicle.
- Install a new seal washer to the condenser side of the discharge hose. Refer to
Sealing Washer Replacement .
- Remove cap or tape from the discharge port on the condenser.
- Connect the discharge hose to the condenser.
- Install the discharge hose to condenser nut.
Tighten
Tighten the nut to 16 N·m (12 lb ft).
- Evacuate and recharge the A/C system. Refer to
Refrigerant Recovery and Recharging .
- Leak test the fittings of the component using
J 39400-A .
- Install the air cleaner assembly. Refer to
Air Cleaner Assembly Replacement.
Discharge Hose Replacement LY7
Tools Required
J 39400-A
Halogen Leak Detector
Removal Procedure
- Remove the air cleaner assembly. Refer to
Air Cleaner Assembly Replacement
.
- Recover the refrigerant from the A/C system. Refer to
Refrigerant Recovery and Recharging
.
- Remove the discharge hose to condenser bolt.
- Disconnect the discharge hose from the condenser.
Important: Cap or tape the open A/C components immediately to prevent A/C system contamination.
- Cap or tape the discharge port on the condenser.
- Remove the lower air baffle. Refer to
Radiator Air Baffle Assemblies and Deflectors
.
- Remove the discharge hose to compressor bolt.
- Disconnect the discharge hose from the compressor.
- Cap or tape the compressor discharge port.
- Remove the discharge hose.
- Remove and discard the sealing washers.
Installation Procedure
- Install a new sealing washer onto the compressor side of the discharge hose. Refer to
Sealing Washer Replacement
.
- Install the discharge hose.
- Remove the cap or tape from the compressor discharge port.
- Connect the discharge hose to the compressor.
Notice: Refer to Fastener Notice in the Preface section.
- Install the discharge hose to compressor bolt.
Tighten
Tighten the bolt to 16 N·m (12 lb ft).
- Install the lower air baffle. Refer to
Radiator Air Baffle Assemblies and Deflectors
.
- Lower the vehicle.
- Install a new seal washer to the condenser side of the discharge hose. Refer to
Sealing Washer Replacement
.
- Remove cap or tape from the discharge port on the condenser.
- Connect the discharge hose to the condenser.
- Install the discharge hose to condenser bolt.
Tighten
Tighten the bolt to 16 N·m (12 lb ft).
- Evacuate and recharge the A/C system. Refer to
Refrigerant Recovery and Recharging
.
- Leak test the fittings of the component using
J 39400-A
.
- Install the air cleaner assembly. Refer to
Air Cleaner Assembly Replacement
.