GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Buick 🢒 2007 🢒 Rendezvous - FWD 🢒 Engine 🢒 Engine Cooling 🢒 Heater Core Replacement

Tools Required

GE-47622 Hose Clamp Pliers

Removal Procedure
  1. Drain the cooling system. Refer to Cooling System Draining and Filling .
  2. Remove the wiper module. Refer to Windshield Wiper System Module Replacement .
  3. Disconnect the brake booster vacuum hose and reposition.
  4. Remove the air cleaner outlet duct. Refer to Air Cleaner Outlet Duct Replacement .
  5. Remove the transmission fluid filler tube. Refer to Transmission Fluid Filler Tube Replacement .

    6. Object Number: 819323 Size: SH
  6. Disconnect both of the heater hose clamps at the heater core using the GE-47622 .
  7. Disconnect the heater hoses from the heater core.

    8. Important: Cap off the heater core inlet and outlet pipes to prevent coolant spillage inside of the vehicle.

  8. Cap off the heater core pipes.
  9. Remove the right instrument panel (I/P) insulator. Refer to Instrument Panel Insulator Panel Replacement - Right Side .
  10. Remove the left I/P insulator. Refer to Instrument Panel Insulator Panel Replacement - Left Side .
  11. Remove the center floor air outlet. Refer to Floor Air Outlet Replacement - Center .

    12. Object Number: 825398 Size: SH
  12. Remove the screws retaining the heater outlet duct.
  13. Remove the heater outlet duct.
  14. Remove the I/P harness to heater core cover tie strap.

    15. Object Number: 825396 Size: SH
  15. Remove the screws retaining the heater core cover.
  16. Remove the heater core cover.

    17. Object Number: 825397 Size: SH
  17. Remove the heater core pipe retaining screw.
  18. Remove the heater core from the HVAC module.

Installation Procedure
  1. Install the heater core to the HVAC module case.

    2. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 825397 Size: SH
  2. Install the heater core pipe retaining clamp screw.

    3. Tighten
    Tighten the screw to 0.9 N·m (8 lb in).


    Object Number: 825396 Size: SH
  3. Install the heater core cover.
  4. Install the heater core cover retaining screws.

    5. Tighten
    Tighten the screws to 0.9 N·m (8 lb in).


    Object Number: 825398 Size: SH
  5. Install the heater outlet duct.
  6. Install the heater outlet duct screws.

    7. Tighten
    Tighten the screws to 0.9 N·m (8 lb in).

  7. Install the I/P harness to heater core cover tie strap.
  8. Install the center floor air outlet. Refer to Floor Air Outlet Replacement - Center .
  9. Install the left I/P insulator. Refer to Instrument Panel Insulator Panel Replacement - Left Side .
  10. Install the right I/P insulator. Refer to Instrument Panel Insulator Panel Replacement - Right Side .

    11. Object Number: 819323 Size: SH
  11. Install the heater hoses to the heater core.
  12. Connect the heater hose clamps using the GE-47622 .
  13. Install the transmission fluid filler tube. Refer to Transmission Fluid Filler Tube Replacement .
  14. Install the air cleaner outlet duct. Refer to Air Cleaner Outlet Duct Replacement .
  15. Connect the brake booster vacuum hose.
  16. Install the wiper module. Refer to Windshield Wiper System Module Replacement .
  17. Fill the coolant. Refer to Cooling System Draining and Filling .