Diagnostic Fault Information
Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Evaporator Temperature Sensor Signal Circuit | B3933.13 | B3933.14 | B3933.14 | -- |
Evaporator Temperature Sensor Low Reference Circuit | -- | 1 | -- | -- |
1 - A/C compressor will not engage | ||||
Circuit Description
The HVAC control module monitors the temperature of the refrigerant through the evaporator via an evaporator temperature sensor. When the refrigerant temperature is low the sensor resistance and the signal voltage are high. When the refrigerant temperature is high the sensor resistance and the signal voltage are low. The sensor works in conjunction with a switch to meter the flow of refrigerant therefore preventing the freezing of moisture that condenses on the evaporator. An evaporator with too little refrigerant will starve causing insufficient cooling. An evaporator flooded with refrigerant will also cause poor cooling when there is too much liquid refrigerant that cannot vaporize quickly.
DTC Descriptor
This diagnostic procedure supports the following DTC:
B3933 Air Conditioning (A/C) Evaporator Temperature Sensor Circuit
Conditions for Running the DTC
The ignition is turned ON.
Conditions for Setting the DTC
The HVAC control module detects the signal circuit is less than 5 counts (0.09 volt).
Action Taken When the DTC Sets
| • | The HVAC control module will store the trouble code in memory. |
| • | A default value will be used for the sensor data by the HVAC control module to allow the A/C system to operate. |
Conditions for Clearing the DTC
| • | The DTC will become history if the HVAC control module no longer detects a failure. |
| • | The history DTC will clear after 50 fault-free ignition cycles. |
| • | The DTC can be cleared with a scan tool. |
Diagnostic Aids
If the condition is not present, refer to Testing for Intermittent Conditions and Poor Connections .
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests for the proper operation of the circuit in the high voltage range.
-
This step tests for the proper operation of the circuit in the low voltage range. If the fuse in the jumper opens when you perform this test, the signal circuit is shorted to voltage.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Schematic Reference: HVAC Schematics Connector End View Reference: HVAC Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
2 |
Does the scan tool indicate that the Evaporator Temp parameter is within the specified range? | -50 to +143°C (-58 to +290°F) | Go to Diagnostic Aids | Go to Step 3 |
Does the scan tool indicate that the Evaporator Temp sensor parameter is equal to the specified value? | -43°C (-45°F) | Go to Step 5 | Go to Step 4 | |
Does the scan tool indicate that the EvaporatorTemp parameter is equal to the specified value? | 144°C (291°F) | Go to Step 8 | Go to Step 6 | |
5 | Test the signal circuit of the evaporator temperature sensor for a short to ground. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 9 |
6 | Test the signal circuit of the evaporator temperature sensor for a short to voltage, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 7 |
7 | Test the low reference circuit of the evaporator temperature sensor for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 9 |
8 | Inspect for poor connections at the harness connector of the evaporator temperature sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 10 |
9 | Inspect for poor connections at the harness connector of the HVAC control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 11 |
10 | Replace the evaporator temperature sensor. Refer to Evaporator Temperature Sensor Replacement . Did you complete the replacement? | -- | Go to Step 12 | -- |
11 | Replace the HVAC control module. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 12 | -- |
12 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
