Steering Shaft, Lower Bearing, and Jacket - Assemble - Off Vehicle for Buick Riviera 1999

Steering Shaft, Lower Bearing, and Jacket - Assemble - Off Vehicle Olds

Important: The steering column support assembly must be replaced if the column has been staked 3 times.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

1. Install the steering column support assembly to the steering column jacket assembly and secure using 4 TORX® head screws.

Tighten
Tighten the screws to 14 N·m (18 lb ft).




2. Apply synthetic grease to the exposed shaft engagement areas.
3. Install the lower shaft to the race and upper shaft assembly using the alignment marks from the disassembled procedure.



4. Install the steering shaft assembly (2) to the steering column tilt head assembly (1).



5. Install the steering shaft assembly with the steering column tilt head assembly into the steering column jacket support assembly.



6. Install 2 pivot pins (1).

Stake the pivot pins in  3 locations (1).




7. Install the adapter and bearing assembly (1).
8. Install the lower bearing seat (2).
9. Install the lower bearing spring (3).
10. Install the lower spring retainer (4).
11. Install the tilt spring assembly only. Refer to Tilt Spring - Assemble - Off Vehicle .
12. Install the ignition switch assembly only. Refer to Ignition and Key Alarm Switch Assembly - Disassemble - Off Vehicle .
13. Install the pivot and pulse switch assembly only . Refer to Windshield Wiper and Washer Switch Assembly - Assemble - Off Vehicle .
14. Install the turn signal and multifunction switch assembly only. Refer to Turn Signal and Multifunction Switch Assembly - Assemble - Off Vehicle .
15. Install the steering column lock cylinder set. Refer to Steering Column Lock Cylinder Set - Assemble - Off Vehicle .

Steering Shaft, Lower Bearing, and Jacket - Assemble - Off Vehicle Buick

Important: The steering column support assembly must be replaced if the column has been staked 3 times.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

1. Install the steering column support assembly to the steering column jacket assembly and secure using 4 TORX® head screws.

Tighten
Tighten the screws to 14 N·m (18 lb ft).




2. Apply synthetic grease to the exposed shaft engagement areas.
3. Install the lower shaft to the race and upper shaft assembly using the alignment marks from the disassembled procedure.



4. Install the steering shaft assembly (2) to the steering column tilt head assembly (1).



5. Install the steering shaft assembly with the steering column tilt head assembly into the steering column jacket support assembly.



6. Install 2 pivot pins (1).

Stake the pivot pins in  3 locations (1).




7. Install the adapter and bearing assembly (1).
8. Install the lower bearing seat (2).
9. Install the lower bearing spring (3).
10. Install the lower spring retainer (4).
11. Install the tilt spring assembly only. Refer to Tilt Spring - Assemble - Off Vehicle .
12. Install the ignition switch assembly only. Refer to Ignition and Key Alarm Switch Assembly - Assemble - Off Vehicle .
13. Install the turn signal and multifunction switch assembly only. Refer to Turn Signal and Multifunction Switch Assembly - Assemble - Off Vehicle .
14. Install the steering column lock cylinder set. Refer to Steering Column Lock Cylinder Set - Assemble - Off Vehicle .