GM Service Manual Online
For 1990-2009 cars only

Object Number: 30394  Size: MF
Engine Controls Components
Engine Data Sensors
OBD II Symbol Description Notice
Handling ESD Sensitive Parts Notice
Handling ESD Sensitive Parts Notice

Circuit Description

While the engine is warming, the PCM monitors the ECT sensor to determine how long it takes the engine to reach the coolant temperature required for Closed Loop operation. DTC P0125 will set if the PCM determines that the engine does not reach Closed Loop temperature in a specified amount of time. This test will not run if either the intake air or engine coolant temperature is too low at start up. The PCM will only run this DTC on a cold start and only once per cold start.

Conditions for Setting the DTC

    • DTCs P0112, P0113, P0117, P0118, not set.
    • Engine coolant and intake air temperature are greater than 10°C (50°F) at start-up.
    • Vehicle speed greater than 8 km/h (5 mph).
    • Closed loop coolant temperature, 60°C (140°F), is not reached within about 7 minutes.

Action Taken When the DTC Sets

    • The PCM will illuminate the Malfunction Indicator Lamp (MIL) on the second consecutive drive trip that the diagnostic runs and fails.
    • The PCM will record operating conditions at the time the diagnostic fails. The first time the diagnostic fails, this information will be stored in Failure Records. If the diagnostic reports a failure on the second consecutive drive trip, the operating conditions at the time of failure will be written to Freeze Frame and the Failure record will be updated.

Conditions for Clearing the MIL/DTC

    • The PCM will turn the MIL OFF after three consecutive drive trips that the diagnostic runs and does not fail.
    • A last test failed (Current DTC) will clear when the ignition is cycled and the diagnostic runs and does not fail.
    • A History DTC will clear after forty consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • PCM battery voltage is interrupted.
    • Using a Scan tool.

Diagnostic Aids

    • Using Freeze Frame and/or Failure Records data may aid in locating an intermittent condition. If the DTC cannot be duplicated, the information included in the Freeze Frame and/or Failure Records data can be useful in determining how many miles since the DTC set. The Fail Counter and Pass Counter can also be used to determine how many ignition cycles the diagnostic reported a pass and/or a fail. Operate vehicle within the same freeze frame conditions (RPM, load, vehicle speed, temperature etc.) that were noted. This will isolate when the DTC failed. For intermittents, refer to Symptoms .
    • If other DTCs are set that share the same ground and/or 5.0 volt reference circuit, check for faulty connections and for poor wiring.
    • If the engine has been allowed to sit overnight, the engine coolant temperature and the intake air temperature values should display within a few degrees of each other. If the temperatures are not within 3°C (5°F), refer to Temperature vs Resistance .
    •  If it is determined that the DTC occurs intermittently, performing the P1114 or P1115 diagnostics table may isolate the cause of the fault.
    •  If the engine coolant temperature exceeds 60°C (140°F), this indicates that the engine is capable of reaching the proper temperature, but not necessarily in the correct amount of time. This diagnostic table must be repeated on a cold engine, engine coolant and intake air temperature less than 50°C (122°F) and within 3°C (5°F) of each other, and the time required to reach the temperature threshold must be measured. When starting a cold engine, measure the amount of time it takes the engine to reach the specified temperature. The engine should reach the specified temperature within 7 minutes. If the specified temperature is not reached within 7 minutes, check the following:
      • Coolant level.
      • Thermostat operation.
      • Are fans on at all times?
      • Refer to Engine Cooling System (6B) for additional information.

Test Description

Number(s) below refer to step numbers on the diagnostic table.

  1. An ECT failure could cause a DTC P0125 to set, so correct any ECT DTCs that are set. For any test that requires probing the PCM or a component harness connector, must use the Connector Test Adapter Kit J 35616-A. Using this kit will prevent damage to the harness connector terminals.

  2. If it is obvious that the engine is not reaching full operating temperature, for example the radiator hoses never get very warm, or there is a complaint of little or no heat from the heater, this step could be skipped.

Step

Action

Value(s)

Yes

No

1

Was the Powertrain On-Board Diagnostic (OBD) System Check performed?

--

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

2

Are any engine coolant temperature DTCs set?

--

Go to applicable DTC table

Go to Step 3

3

  1. Install the scan tool.
  2. Turn the ignition ON, engine OFF.
  3. Disconnect the ECT sensor.

Does the scan tool indicate the ECT sensor is less than the specified value?

-35°C (-31°F)

Go to Step 4

Go to DTC P0117 Engine Coolant Temperature (ECT) Sensor Circuit Low Voltage

4

Using a jumper wire, jumper terminals at the ECT sensor harness connector together.

Does the scan tool indicate the ECT is greater than the specified value?

150°C (302°F)

Go to Step 5

Go to DTC P0118 Engine Coolant Temperature (ECT) Sensor Circuit High Voltage

5

  1. Reconnect the ECT sensor.
  2. Start and idle the engine.
  3. With the engine idling, observe the ECT sensor display on the Engine 1 Data List of the scan tool.

Important: Allow time for the engine to warm up if it has not already reached the specified temperature. 7 minutes is the maximum amount of time it should take to reach this temperature from a cold start. Less time should be necessary if the engine is already warm.

Does the scan tool indicate the engine coolant temperature reached the specified value?

60°C (140°F)

System must be rechecked on a cold start. Refer to Diagnostic Aids.

Go to Step 6

6

Using a DVM (J 39200), measure the resistance of the ECT sensor. Refer to Temperature vs Resistance .

Is the ECT resistance close to the value indicated in the Temperature Vs Resistance Table?

--

Go to Step 7

Go to Step 8

7

For an engine cooling system problem, check for the following conditions:

    • Thermostat operation
    • Coolant level
    • Coolant to water ratio
    • Cooling fan operation etc.

Refer to Engine Cooling System.

Is the action complete?

--

Go to Step 9

--

8

Replace the ECT sensor. Refer to Engine Coolant Temperature Sensor Replacement .

Is the action complete?

--

Go to Step 9

--

9

  1. Using the scan tool, select DTC, Clear Info.
  2. Start the engine and idle at normal operating temperature.
  3. Select DTC Specific, then enter the DTC number which was set.
  4. Operate the vehicle within the conditions for setting this DTC as specified in the supporting text, if applicable.

Does the scan tool indicate that this test ran and passed?

--

Go to Step 10

Go to Step 2

10

Using the scan tool, select Capture Info, Review Info.

Are any DTCs displayed that have not been diagnosed?

--

Go to the applicable DTC table

System OK