DTC P1573 Lost Communications with Brake/Traction Control (EBTCM) System. Buick Skylark 1997

For 1990-2009 cars only

Makes 🢒 Buick 🢒 1997 🢒 Skylark 🢒 Engine 🢒 Engine Controls - 3.1L 🢒 DTC P1573 Lost Communications with Brake/Traction Control (EBTCM) System

Refer to

Power, Ground, MIL, and DLC

Engine Controls Components
Information Sensors
Ignition Controls
OBD II Symbol Description Notice
Handling ESD Sensitive Parts Notice
Handling ESD Sensitive Parts Notice
.

Refer toSerial Data Line in Electrical Diagnosis.

The PCM uses the UART serial data line (CKT 800) to communicate with various other components and systems within the vehicle. If the PCM does not receive data from the Electronic Brake and Traction Control Module (EBTCM), the PCM will store DTC P1573 indicating loss of communication with the ABS/TCS system.

Conditions for Setting the DTC

The PCM has detected a PCM - EBTCM communication error for 0.5 second.

Action Taken When the DTC Sets

•	The PCM will not illuminate the malfunction indicator lamp (MIL).

•	The PCM will store conditions which were present when the DTC set as Failure Records data only. This information will not be stored as Freeze Frame data.

Conditions for Clearing the MIL/DTC

•	A History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.

•	The DTC can be cleared by using the scan tool Clear Info function.

Diagnostic Aids

An intermittent may be caused by a poor connection, rubbed through wire insulation, or a wire broken inside the insulation. Check for the following conditions:

•	Poor Connection or Damaged Harness. Inspect the vehicle wiring harness for an open or short to ground in CKT 800, improper mating, broken locks, improperly formed or damaged terminals, poor terminal to wire connection, and damaged harness.

•

Intermittent Test - Observe ABS data on the scan tool while moving harness and related connectors. Refer to UART Data Line in Electrical for a complete mechanization of CKT 800 and devices using the UART serial data line. If failure is induced, the scan tool data will stop updating. This may help to isolate the location of the malfunction.

•	If the above items have been checked and no problem is found but DTC P1573 continues to set, replace the PCM.

Reviewing the Fail Records vehicle mileage after the diagnostic test last failed may help determine how often the condition that caused the DTC to be set occurs. This may assist in diagnosing the condition.

Test Description

Number(s) below refer to the step number(s) on the Diagnostic Table.

Checks to see if the Electronic Brake and Traction Control Module (EBTCM) is able to transmit data and ensures that CKT 800 to the EBTCM is not open.

DTC P1573 - PCM/EBTCM Serial Data Circuit

Step	Action	Value(s)	Yes	No
1	Was the Powertrain On-Board Diagnostic (OBD) System Check performed?	--	Go to Step 2	Go to Powertrain On Board Diagnostic (OBD) System Check
2	Attempt to select ABS data with the scan tool. Can ABS data be displayed?	--	Go to Step 3	Go to Step 4
3	Turn OFF the ignition switch. Disconnect the PCM and the EBTCM. Check the UART serial data circuit for an open between the EBTCM and the PCM. If a problem is found, repair as necessary. Refer to Repair Procedures in Electrical Diagnosis. Was a problem found?	--	Go to Step 8	Go to Step 5
4	Turn OFF the ignition switch. Disconnect the EBTCM. Turn ON the ignition switch. Using a digital multimeter, measure voltage between the serial data circuit at the EBTCM harness connector and ground. Does voltage constantly vary between the specified values?	0-5V	Go to Step 6	Go to UART Data Line in Electrical Diagnosis
5	Check the UART serial data circuit for a poor connection at the PCM. If a problem is found, repair as necessary. Refer to Repair Procedures in Electrical Diagnosis. Was a problem found?	--	Go to Step 8	Refer to Diagnostic Aids
6	Check the UART serial data circuit for a poor connection at the EBTCM If a problem is found, repair as necessary. Refer to Repair Procedures in Electrical Diagnosis. Was a problem found?	--	Go to Step 8	Go to Step 7
7	Replace the EBTCM. Refer to On-Vehicle Service in ABS/TCS. Is Action complete?	--	Go to Step 8	--
8	Review and record scan tool Fail Records data. Clear DTCs. Operate the vehicle within Fail Records conditions. Using a scan tool, monitor Specific DTC info for DTC P1573 Does the scan tool indicate DTC P1573 failed?	--	Go to Step 2	System OK