GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Buick 🢒 2005 🢒 Terraza - 4WD 🢒 Vehicle Control Systems 🢒 Vehicle DTC Information 🢒 Power Window Inoperative - Driver Door

Diagnostic Instructions

Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Driver Window Switch B+

1

1

--

--

Passenger Window Switch B+

2

2

--

--

Passenger Window Switch Down Signal

2

2

2

--

Passenger Window Switch Up Signal

2

2

2

--

Driver Window Motor Control

1

1

1

--

Passenger Window Motor Control

2

2

2

--

Driver Window Switch Ground

--

1, 2

1, 2

--

1. Driver Window Malfunction

2. Passenger Window Malfunction

Circuit/System Description

When the ignition switch is in the RUN or ACCY position and the driver or passenger window switch is pressed in the down position, voltage is applied to the appropriate window motor causing that window to open. When the driver or passenger window switch is pulled in the up position, voltage is applied to the appropriate window motor in the opposite direction causing that window to close.

Reference Information

Schematic Reference

Power Window Schematics

Connector End View Reference

Power Door Systems Connector End Views

Description and Operation

Power Windows Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Circuit/System Verification

Ignition ON, command the driver window UP and DOWN using the driver window switch. The driver window should perform the UP and DOWN functions.

Circuit/System Testing
  1. Ignition OFF, disconnect the harness connector at the driver window switch.
  2. Test for less than 1 ohm between the ground circuit terminal F and ground.
    3. ⇒If greater than the specified range, test the ground circuit for an open/high resistance.
  3. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal C and ground.
    4. ⇒If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
  4. Ignition OFF, connect the harness connector at the driver window switch and disconnect the harness connector at the driver window motor.
  5. Test for less than 1 ohm between the control circuit terminal B and ground.
    6. ⇒If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, test or replace the driver window switch.
  6. Test for less than 1 ohm between the control circuit terminal A and ground.
    7. ⇒If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, test or replace the driver window switch.
  7. Connect a test lamp between control circuit terminal B and control circuit terminal A.
  8. Ignition ON, command the driver door window UP and DOWN using the driver window switch. The test lamp should illuminate when commanding the UP and DOWN states.
    9. ⇒If the test lamp does not illuminate during either of the commands, test both control circuits for a short to ground. If the circuits test normal, test or replace the driver window switch.
  9. If all circuits tests normal, test or replace the driver window motor.

Component Testing

Driver Window Switch

  1. Ignition OFF, disconnect the harness connector at the driver window switch.
  2. Test for infinite resistance between the control terminals A and D and the ignition terminal C with the RF window switch in the inactive position.
    3. ⇒If not the specified value, replace the driver window switch.
  3. Test for less than 2 ohms between the control terminal A and the ignition terminal C with the RF window switch in the up position.
    4. ⇒If greater than the specified range, replace the driver window switch.
  4. Test for less than 2 ohms between the control terminal D and the ignition terminal C with the RF window switch in the down position.
    5. ⇒If greater than the specified range, replace the driver window switch.
  5. Test for infinite resistance between the control terminals G and H and the ignition terminal C with the driver window switch in the inactive position.
    6. ⇒If not the specified value, replace the driver window switch.
  6. Test for less than 2 ohms between the control terminal G and the ignition terminal C with the driver window switch in the up position.
    7. ⇒If greater than the specified range, replace the driver window switch.
  7. Test for less than 2 ohms between the control terminal H and the ignition terminal C with the driver window switch in the down position.
  8. If greater than the specified range, replace the driver window switch.

Window Motor

  1. Ignition OFF, disconnect the harness connector at the appropriate window motor.
  2. Install a 25A fused jumper wire between one of the control terminals and 12V. Momentarily install a jumper wire between the other control terminal and ground. Reverse the jumper wires at least two times, the window motor should perform the UP/DOWN functions
    3. ⇒If it does not perform as specified, replace the driver window motor.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Front Side Door Window Switch Replacement - Left Side
    •  Front Side Door Window Regulator Motor Replacement