Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle

Depress the horn switch.

Do the horns operate?

Go to Step 3

Go to Step 5

1. Install a scan tool.
2. Turn ON the ignition, with the engine OFF.
3. With a scan tool, command the body control module (BCM) horn output ON and OFF.

Do the horns operate?

Go to Testing for Intermittent Conditions and Poor Connections

Go to Step 4

4

Test the dash integration module (DIM) portion of the horn relay control circuit for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 21

Go to Step 11

5

1. Turn OFF the ignition.
2. Disconnect the horn relay.
3. Connect a test lamp between the battery positive voltage circuit of the horn relay coil and a good ground.

Does the test lamp illuminate?

Go to Step 6

Go to Step 14

1. Connect a test lamp between the battery positive voltage circuit of the horn relay coil and the horn relay control circuit.
2. Depress and hold the horn switch.

Does the test lamp illuminate?

Go to Step 7

Go to Step 15

7

Connect a test lamp between the battery positive voltage circuit of the horn relay switch and a good ground.

Does the test lamp illuminate?

Go to Step 8

Go to Step 16

Momentarily connect a 15-amp fused jumper wire between the battery positive voltage circuit of the horn relay switch and the horn control circuit.

Do the horns operate?

Go to Step 12

Go to Step 9

1. Reconnect the horn relay.
2. Disconnect either horn connector.
3. Connect a test lamp between the horn control circuit and a good ground.
4. Depress and hold the horn switch.

Does the test lamp illuminate?

Go to Step 10

Go to Step 17

1. Connect a test lamp between the horn control circuit and the horn ground circuit.
2. Depress and hold the horn switch.

Does the test lamp illuminate?

Go to Step 13

Go to Step 18

Inspect for poor connections at the harness connector of the DIM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 21

Go to Step 19

Inspect for poor connections at the horn relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 21

Go to Step 20

13

Repair the high resistance in the horn control circuit or the horn ground circuit. A resistance as low as 0.5 ohm could cause operating problems with the horns. Also, though unlikely, it is possible that both horns are defective. Refer to Circuit Testing and Wiring Repairs .

Did you complete the repair?

Go to Step 21

--

Repair the open or high resistance in the battery positive voltage circuit of the horn relay coil. Refer to Circuit Testing and Wiring Repairs .

Did you complete the repair?

Go to Step 21

--

15

Repair the open or short to voltage in the horn relay control circuit. The horn relay control circuit includes the horn slip ring and the horn switch. Refer to Circuit Testing and Wiring Repairs .

Did you complete the repair?

Go to Step 21

--

Repair the open or high resistance in the battery positive voltage circuit of the horn relay switch. Refer to Circuit Testing and Wiring Repairs .

Did you complete the repair?

Go to Step 21

--

Repair the open or high resistance in the horn control circuit. Refer to Circuit Testing and Wiring Repairs .

Did you complete the repair?

Go to Step 21

--

Repair the open or high resistance in the horn ground circuit. Refer to Circuit Testing and Wiring Repairs .

Did you complete the repair?

Go to Step 21

--

Important: Perform the DIM programming procedure when replacing the DIM.

Replace the DIM. Refer to Control Module References for replacement, setup, and programming.

Did you complete the repair?

Go to Step 21

--

Replace the horn relay.

Did you complete the replacement?

Go to Step 21

--

Operate the horns.

Do the horns operate properly?

System OK

Go to Step 1