GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2005 🢒 CTS 🢒 Brakes 🢒 Antilock Brake System 🢒 DTC C0138 or C0139

Circuit Description

The electronic brake control module (EBCM) uses the input from the brake fluid pressure sensor for more accurate braking control during vehicle stability enhancement system (VSES).

DTC Descriptors

This diagnostic procedure supports the following DTCs:

    • DTC C0138 Base Brake System Pressure Circuit Low
    • DTC C0139 Base Brake System Pressure Circuit High

Conditions for Running the DTC

DTC C0138

    • The ignition is ON.
    • Ignition voltage is greater than 8 volts.

DTC C0139

    • The ignition is ON.
    • Ignition voltage is greater than 8 volts.
    • The vehicle speed is greater than 16 km/h (10 mph).

Conditions for Setting the DTC

DTC C0138

The vehicle speed exceeds 25 km/h (15 mph) then decelerates by 11.5 km/h (7 mph) per second and the brake pressure never increases.

DTC C0139

One of the following conditions occur:

    • Brake pressure does not change after brake pedal has been applied twice.
    • While brake pressure is greater than 50 psi, the vehicle speed exceeds 40 km/h (24 mph) and vehicle acceleration exceeds 8 km/h (5 mph) per second twice.

Action Taken When the DTC Sets
    • The EBCM disables the PBA/TCS/VSES for the duration of the ignition cycle.
    • The Traction Control and Active Handling indicator turns ON.
    • The DIC displays the Service Stability System message.
    • The ABS remains functional.

Conditions for Clearing the DTC
    • The condition for the DTC is no longer present and the DTC is cleared with a scan tool.
    • The EBCM automatically clears the history DTC when a current DTC is not detected in 100 consecutive drive cycles.

Diagnostic Aids
    • Find out from the driver under what conditions the DTC was set (when the DIC displayed the Service Active Handling message). This information will help to duplicate the failure.
    • The Snapshot function on the scan tool can help find an intermittent DTC.
    • Brake pressure sensor internal malfunction.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step tests for the proper operation of the circuit in the low voltage range.

    2.

  2. This step tests for the proper operation of the circuit in the high voltage range. If the fuse in the jumper opens when you perform this test, the signal circuit is shorted to ground.

    3.

  3. This step tests for a short to voltage in the 5-volt reference circuit.

    4.

  4. This step tests for a high resistance or an open in the low reference circuit.

Step

Action

Values

Yes

No

Schematic Reference: Antilock Brake System Schematics

Connector End View Reference: Antilock Brake System Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle

2
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the Brake Fluid Pressure Sensor Input parameter in the VSES data list.

Does the scan tool display that the Brake Fluid Pressure Sensor Input parameter is within the specified range?

0.14-4.9 V

Go to Diagnostic Aids

Go to Step 3

3

  1. Turn OFF the ignition.
  2. Disconnect the brake fluid pressure sensor connector.
  3. Turn ON the ignition, with the engine OFF.
  4. With the scan tool, observe the Brake Fluid Pressure Sensor Input parameter.

Does the scan tool indicate that the Brake Fluid Pressure Sensor Input parameter is less than the specified value?

0.14 V

Go to Step 4

Go to Step 10

4

  1. Turn OFF the ignition.
  2. Connect a 3-amp fused jumper wire between the 5-volt reference circuit of the brake fluid pressure sensor and the signal circuit of the brake fluid pressure sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. With the scan tool, observe the Brake Fluid Pressure Sensor Input parameter.

Does the scan tool indicate that the Brake Fluid Pressure Sensor Input parameter is greater than the specified value?

4.9 V

Go to Step 5

Go to Step 8

5

  1. Disconnect the fused jumper wire.
  2. Measure the voltage between the 5-volt reference circuit of the brake fluid pressure sensor and the low reference circuit of the brake fluid pressure sensor.

Does the voltage measure less the specified value?

5 V

Go to Step 6

Go to Step 7

6

  1. Turn OFF the ignition.
  2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  3. Measure the resistance from the low reference circuit of the brake fluid pressure sensor to a good ground.

Does the resistance measure less than the specified value?

5 ohms

Go to Step 12

Go to Step 11

7

Test the 5-volt reference circuit of the brake fluid pressure sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 16

Go to Step 13

8

Test the 5-volt reference circuit of the brake fluid pressure sensor for the following conditions:

    • An open
    • A short to ground
    • A high resistance

Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 16

Go to Step 9

9

Test the signal circuit of the brake fluid pressure sensor for the following conditions:

    • An open
    • A short to ground
    • A high resistance

Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 16

Go to Step 13

10

Test the signal circuit of the brake fluid pressure sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 16

Go to Step 13

11
  1. Disconnect the electronic brake control module (EBCM) harness connector.
  2. Install the J 39700 Universal Pinout Box using the J 39700-300 Cable Adapter to the EBCM harness connector only.
  3. Test the low reference circuit of the brake fluid pressure sensor for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 16

Go to Step 13

12

Inspect for poor connections at the harness connector of the brake fluid pressure sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

--

Go to Step 16

Go to Step 14

13

Inspect for poor connections at the harness connector of the EBCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

--

Go to Step 16

Go to Step 15

14

Replace the brake fluid pressure sensor. Refer to Brake Pressure Modulator Valve Pressure Sensor Replacement .

Did you complete the replacement?

--

Go to Step 16

--

15

Replace the EBCM. Refer to Control Module References for replacement, setup and programming.

Did you complete the replacement?

--

Go to Step 16

--

16
  1. Clear the DTCs using the scan tool.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

--

Go to Step 2

System OK