Front Brake Hose Replacement RWD

Caution: Refer to Brake Dust Caution in the Preface section.

Caution: Refer to Brake Fluid Irritant Caution in the Preface section.

Notice: Refer to Brake Fluid Effects on Paint and Electrical Components Notice in the Preface section.

1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
2. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.



3. Disconnect the front brake pipe fitting (1).

Cap the brake pipe fitting to prevent brake fluid loss and contamination.




4. Remove the front brake hose retainer clip (1).



5. Remove the rear lower shock module bolt (1).



6. Remove the brake hose fitting bolt (1).
7. Remove the brake hose fitting gaskets (2) from the brake hose (3).

Discard the brake hose fitting gaskets.

8. Remove the brake hose.

1. Assemble the brake hose fitting bolt (1) with 2 new brake hose fitting gaskets (2) to the brake hose (3).

Notice: Refer to Fastener Notice in the Preface section.

2. Install the brake hose assembly to the caliper.

Tighten
Tighten the brake hose fitting bolt to 49 N·m (36 lb ft).




3. Install the rear lower shock module bolt (1) through the brake hose bracket and to the lower control arm.

Tighten
Tighten the bolt to 25 N·m (18 lb ft).




4. Install the front brake hose retainer clip (1).



5. Connect the front brake pipe fitting (1).

Tighten
Tighten the fitting to 18 N·m (13 lb ft).

6. Bleed the hydraulic brake system. Refer to Hydraulic Brake System Bleeding.
7. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.

Front Brake Hose Replacement AWD

Caution: Refer to Brake Dust Caution in the Preface section.

Caution: Refer to Brake Fluid Irritant Caution in the Preface section.

Notice: Refer to Brake Fluid Effects on Paint and Electrical Components Notice in the Preface section.

1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
2. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.



3. Disconnect the front brake pipe fitting (1).

Cap the brake pipe fitting to prevent brake fluid loss and contamination.




4. Remove the front brake hose retainer clip (1).



5. Remove the brake hose retainer bolt (1).
6. Disconnect the wheel speed sensor wire harness clip (2) from the brake hose retainer.



7. Remove the brake hose fitting bolt (1).
8. Remove the brake hose fitting gaskets (2) from the brake hose (3).

Discard the brake hose fitting gaskets.

9. Remove the brake hose.

1. Assemble the brake hose fitting bolt (1) with 2 new brake hose fitting gaskets (2) to the brake hose (3).

Notice: Refer to Fastener Notice in the Preface section.

2. Install the brake hose assembly to the caliper.

Tighten
Tighten the brake hose fitting bolt to 49 N·m (36 lb ft).




3. Install the brake hose retainer bolt (1).

Tighten
Tighten the brake hose retainer bolt to 10 N·m (89 lb in).

4. Connect the wheel speed sensor wire harness clip (2) to the brake hose retainer.



5. Install the front brake hose retainer clip (1).



6. Connect the front brake pipe fitting (1).

Tighten
Tighten the fitting to 18 N·m (13 lb ft).

7. Bleed the hydraulic brake system. Refer to Hydraulic Brake System Bleeding.
8. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.