Front Brake Caliper Bracket Replacement RWD

Warning: Refer to Brake Dust Warning in the Preface section.

1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
2. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.



3. Using a backup wrench on the brake caliper guide pins, remove the guide pin bolts (1).

Caution: Support the brake caliper with heavy mechanic wire, or equivalent, whenever it is separated from its mount and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak.

4. Remove the brake caliper and support with heavy mechanics wire or equivalent.



5. Remove the outer brake pad (1).
6. Remove the inner brake pad (2).
7. Remove the brake pad springs.



8. Remove the brake caliper bracket bolts (1).



9. Remove the brake caliper bracket (1).
10. Inspect the disc brake hardware. Refer to Front Disc Brake Mounting and Hardware Inspection.

1. Install the brake caliper bracket (1).

Note: If reusing the caliper bracket bolts the threads of the caliper bracket bolts and the threads of the knuckle mounting holes must be free of residue and debris prior to application of threadlocker in order to ensure proper adhesion and fastener retention.

2. Prepare the bolts and the threaded holes for assembly:

•	Thoroughly clean the residue from the bolt threads by using denatured alcohol or equivalent and allow to dry.

•	Thoroughly clean the residue from the threaded holes by using denatured alcohol or equivalent and allow to dry.

•	Apply threadlocker GM P/N 12345493 (Canada P/N 10953488), or equivalent to 2/3 of the threaded length of the lower caliper bracket bolts. Ensure there are no gaps in the threadlocker along the length of the filled area of the bolts.

•	Allow the threadlocker to cure approximately 10 minutes before installation.

Caution: Refer to Fastener Caution in the Preface section.




3. Install the brake caliper bracket bolts (1) and tighten to  230 N·m (170 lb ft).
4. Install the brake pad springs.



5. Install the outer brake pad (1).
6. Install the inner brake pad (2).

Note: If reusing the caliper bracket bolts the threads of the caliper bracket bolts and the threads of the knuckle mounting holes must be free of residue and debris prior to application of threadlocker in order to ensure proper adhesion and fastener retention.

7. Prepare the bolts and the threaded holes for assembly:

•	Thoroughly clean the residue from the bolt threads by using denatured alcohol or equivalent and allow to dry.

•	Thoroughly clean the residue from the threaded holes by using denatured alcohol or equivalent and allow to dry.

•	Apply threadlocker GM P/N 12345493 (Canada P/N 10953488), or equivalent to 2/3 of the threaded length of the lower caliper bracket bolts. Ensure there are no gaps in the threadlocker along the length of the filled area of the bolts.

•	Allow the threadlocker to cure approximately 10 minutes before installation.




8. Install the brake caliper to the caliper bracket.
9. Using a backup wrench on the brake caliper guide pins, install the guide pin bolts (1) and tighten to  63 N·m (46 lb ft).
10. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.

Front Brake Caliper Bracket Replacement AWD

Warning: Refer to Brake Dust Warning in the Preface section.

1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
2. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.



3. Using a backup wrench on the brake caliper guide pins, remove the guide pin bolts (1).

Caution: Support the brake caliper with heavy mechanic wire, or equivalent, whenever it is separated from its mount and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak.

4. Remove the brake caliper and support with heavy mechanics wire or equivalent.



5. Remove the inner brake pad (1).
6. Remove the outer brake pad (2).
7. Remove the brake pad springs.



8. Remove the brake caliper bracket bolts (1).



9. Remove the brake caliper bracket (1).
10. Inspect the disc brake hardware. Refer to Front Disc Brake Mounting and Hardware Inspection.

1. Install the brake caliper bracket (1).

Note: If reusing the caliper bracket bolts the threads of the caliper bracket bolts and the threads of the knuckle mounting holes must be free of residue and debris prior to application of threadlocker in order to ensure proper adhesion and fastener retention.

2. Prepare the bolts and the threaded holes for assembly:

•	Thoroughly clean the residue from the bolt threads by using denatured alcohol or equivalent and allow to dry.

•	Thoroughly clean the residue from the threaded holes by using denatured alcohol or equivalent and allow to dry.

•	Apply threadlocker GM P/N 12345493 (Canada P/N 10953488), or equivalent to 2/3 of the threaded length of the lower caliper bracket bolts. Ensure there are no gaps in the threadlocker along the length of the filled area of the bolts.

•	Allow the threadlocker to cure approximately 10 minutes before installation.

Caution: Refer to Fastener Caution in the Preface section.




3. Install the brake caliper bracket bolts (1) and tighten to  230 N·m (170 lb ft).
4. Install the brake pad springs.



5. Install the inner brake pad (1).
6. Install the outer brake pad (2).

Note: If reusing the caliper bracket bolts the threads of the caliper bracket bolts and the threads of the knuckle mounting holes must be free of residue and debris prior to application of threadlocker in order to ensure proper adhesion and fastener retention.

7. Prepare the bolts and the threaded holes for assembly:

•	Thoroughly clean the residue from the bolt threads by using denatured alcohol or equivalent and allow to dry.

•	Thoroughly clean the residue from the threaded holes by using denatured alcohol or equivalent and allow to dry.

•	Apply threadlocker GM P/N 12345493 (Canada P/N 10953488), or equivalent to 2/3 of the threaded length of the lower caliper bracket bolts. Ensure there are no gaps in the threadlocker along the length of the filled area of the bolts.

•	Allow the threadlocker to cure approximately 10 minutes before installation.




8. Install the brake caliper to the caliper bracket.
9. Using a backup wrench on the brake caliper guide pins, install the guide pin bolts (1) and tighten to  63 N·m (46 lb ft)..
10. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.