1

4-5-6 Clutch Backing Plate Retaining Ring

2

4-5-6 Clutch Backing Plate

3

4-5-6 Clutch Plate Assembly (Qty: 7)

4

4-5-6 Clutch Plate (Qty: 7)

5

4-5-6 Clutch (Waved) Plate

1

4-5-6 Clutch Piston Dam Retaining Ring

Caution: Use care when compressing the 4-5-6 clutch piston assembly, spring and dam assembly. Compressing the dam assembly too much may damage it.

Caution: Refer to Retaining Ring Reuse Caution in the Preface section.

Special Tool

J 43074 Clutch Spring Compressor

For equivalent regional tools, refer to Special Tools.

2

4-5-6 Clutch Piston Dam Assembly

Tip
It may be necessary to apply air pressure to remove the dam and piston.

3

4-5-6 Clutch Spring

4

4-5-6 Clutch Piston Assembly

Tip
It may be necessary to apply air pressure to remove the piston.

Preliminary Procedures

1

Turbine Shaft Fluid Seal Ring (Qty: 3)

Caution: Do not use old seal rings. Install NEW seal rings. Reusing old seal rings may cause internal transmission leaks and transmission damage.

Caution: Size the fluid seal rings for at least 5 minutes after installation to obtain proper seal ring size. Failure to do so may cause internal transmission leaks and transmission damage.

Tip
Adjust the turn screw on DT 47768-1 seal protector and install the bottom seal ring first.

Special Tools

For equivalent regional tools, refer to Special Tools.

1

4-5-6 Clutch Piston Assembly

2

4-5-6 Clutch Spring

Caution: Ensure the spring tabs are facing up during installation. Failure to do so may cause damage to the clutch assembly.

3

4-5-6 Clutch Piston Dam Assembly

Tip
Lubricate the inner and outer sealing surfaces of the dam assembly with automatic transmission fluid (ATF) in order to ease installation into the piston.

4

4-5-6 Clutch Piston Dam Retaining Ring

Caution: Use care when compressing the 4-5-6 clutch piston assembly, spring and dam assembly. Compressing the dam assembly too much may damage it.

Caution: Refer to Retaining Ring Reuse Caution in the Preface section.

Tip
Apply air to verify proper installation of all 4-5-6 clutch components. The piston should apply and release smoothly.

Special Tool

J 43074 Clutch Spring Compressor

For equivalent regional tools, refer to Special Tools.

1

4-5-6 Clutch (Waved) Plate

2

4-5-6 Clutch Plate (Qty: 7)

3

4-5-6 Clutch Plate Assembly (Qty: 7)

4

4-5-6 Clutch Backing Plate

5

4-5-6 Clutch Backing Plate Retaining Ring

Tip
After the retaining ring is installed, determine clutch piston travel in order to verify if the correct selective retaining ring is being used. Refer to 4-5-6 Clutch Backing Plate Retaining Ring Measurement.

1

4-5-6 Clutch Backing Plate Retaining Ring

2

4-5-6 Clutch Backing Plate

3

4-5-6 Clutch Plate Assembly (Qty: 5)

4

4-5-6 Clutch Plate (Qty: 5)

5

4-5-6 Clutch (Waved) Plate

1

4-5-6 Clutch Piston Dam Retaining Ring

Caution: Use care when compressing the 4-5-6 clutch piston assembly, spring and dam assembly. Compressing the dam assembly too much may damage it.

Caution: Refer to Retaining Ring Reuse Caution in the Preface section.

Special Tool

J 43074 Clutch Spring Compressor

For equivalent regional tools, refer to Special Tools.

2

4-5-6 Clutch Piston Dam Assembly

Tip
It may be necessary to apply air pressure to remove the dam and piston.

3

4-5-6 Clutch Spring

4

4-5-6 Clutch Piston Assembly

Tip
It may be necessary to apply air pressure to remove the piston.

Preliminary Procedures

1

Turbine Shaft Fluid Seal Ring (Qty: 3)

Caution: Do not use old seal rings. Install NEW seal rings. Reusing old seal rings may cause internal transmission leaks and transmission damage.

Caution: Size the fluid seal rings for at least 5 minutes after installation to obtain proper seal ring size. Failure to do so may cause internal transmission leaks and transmission damage.

Tip
Adjust the turn screw on DT-48066-3 seal protector and install the bottom seal ring first.

Special Tools

For equivalent regional tools, refer to Special Tools.

1

4-5-6 Clutch Piston Assembly

2

4-5-6 Clutch Spring

Caution: Ensure the spring tabs are facing up during installation. Failure to do so may cause damage to the clutch assembly.

3

4-5-6 Clutch Piston Dam Assembly

Tip
Lubricate the inner and outer sealing surfaces of the dam assembly with automatic transmission fluid (ATF) in order to ease installation into the piston.

4

4-5-6 Clutch Piston Dam Retaining Ring

Caution: Use care when compressing the 4-5-6 clutch piston assembly, spring and dam assembly. Compressing the dam assembly too much may damage it.

Caution: Refer to Retaining Ring Reuse Caution in the Preface section.

Tip
Apply air to verify proper installation of all 4-5-6 clutch components. Piston should apply and release smoothly.

Special Tool

J 43074 Clutch Spring Compressor

For equivalent regional tools, refer to Special Tools.

1

4-5-6 Clutch (Waved) Plate

2

4-5-6 Clutch Plate (Qty: 5)

3

4-5-6 Clutch Plate Assembly (Qty: 5)

4

4-5-6 Clutch Backing Plate

5

4-5-6 Clutch Backing Plate Retaining Ring

Tip
After the retaining ring is installed, determine clutch piston travel in order to verify if the correct selective retaining ring is being used. Refer to 4-5-6 Clutch Backing Plate Retaining Ring Measurement.