DTC P0562 ECM
Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC P0562: System Voltage LowDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
IGN I | P0562 | P0562 | -- | -- |
Ground | -- | P0562 | -- | -- |
Circuit/System Description
The engine control module (ECM) monitors the system voltage to ensure that the voltage stays within the proper range. Damage to components, and incorrect data may occur when the voltage is out of range.
Conditions for Running the DTC
| • | The vehicle speed is above 8 km/h (5 mph). |
| • | The system voltage is between 9.5-18 V. |
Conditions for Setting the DTC
The ECM detects a system voltage below 10 volts for 5 seconds.
Action Taken When the DTC Sets
| • | The charge indicator turns ON. |
| • | The driver information center (DIC) displays the SERVICE CHARGING SYSTEM message. |
Conditions for Clearing the DTC
DTC P0562 is a C type DTC.
Diagnostic Aids
| • | A low voltage DTC set in multiple modules indicates a concern in the charging system. |
| • | A low voltage value in multiple modules indicates a concern in the charging system. |
| • | Inspect the ECM ground connection, to verify that it is clean tight. |
Reference Information
Schematic Reference
| • | Engine Controls Schematics for the 3.6L engine |
| • | Engine Controls Schematics for the 6.2L engine |
Connector End View Reference
Description and Operation
Charging System Description and Operation
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
- Engine running, accessories OFF, measure and record the battery voltage at the battery terminals. The voltage should be between 12.6 and 15.0 V
- Observe the scan tool ECM Ignition 1 Signal parameter. The reading should be between 12.6 and 15.0 V
| ⇒ | If not within the specified range, refer to Charging System Test. |
Circuit/System Testing
- Ignition OFF, disconnect the harness connectors at the ECM.
- Ignition OFF, and scan tool disconnected, open and close the driver door, and wait 1 minute. Test for less than 5 Ω between the ground circuit terminals listed below and ground.
- Ignition On, verify that a test lamp illuminates between the IGN/B+ circuit terminals listed below and ground:
- If all circuits test normal, replace the ECM.
| • | Terminal 1 X2 (3.6L) |
| • | Terminal 2 X2 (3.6L) |
| • | Terminal 4 X2 (3.6L) |
| • | Terminal 73 X2 (6.2L) |
| • | Terminal 73 X3 (6.2L) |
| ⇒ | If greater than the specified range, test the ground circuit for an open/high resistance. |
| • | Terminal 4 X2 (3.6L) |
| • | Terminal 5 X2 (3.6L) |
| • | Terminal 6 X2 (3.6L) |
| • | Terminal 54 X2 (3.6L) |
| • | Terminal 56 X2 (3.6L) |
| • | Terminal 19 X1 (6.2L) |
| • | Terminal 20 X1 (6.2L) |
| • | Terminal 13 X2 (6.2L) |
| • | Terminal 28 X2 (6.2L) |
| ⇒ | If the test lamp does not illuminate , test the IGN/B+ circuit for a short to ground or an open/high resistance. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for ECM replacement, setup, and programming
DTC P0562 FSCM
Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC P0562: System Voltage Low - FPCMDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
B+ | P0562 | P0562 | -- | -- |
Ground | -- | P0562 | -- | -- |
Circuit/System Description
The fuel pump control module (FPCM) monitors the system voltage to ensure that the voltage stays within the proper range. Damage to components, and incorrect data may occur when the voltage is out of range.
Conditions for Running the DTC
The engine is running.
Conditions for Setting the DTC
The FPCM detects that the battery voltage is less than 9 V.
Action Taken When the DTC Sets
DTC P0562 is a type C DTC.
Conditions for Clearing the DTC
DTC P0562 is a type C DTC.
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Charging System Description and Operation
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing
- Engine running, accessories OFF, measure and record the battery voltage at the battery terminals. The voltage should be between 12.6 and 15.0 V.
- Ignition OFF, disconnect the harness connectors at the FPCM.
- Ignition OFF and scan tool disconnected, open and close the driver door, and wait 1 minute. Test for less than 5 Ω between the ground circuit terminal 1 and ground.
- Verify that a test lamp illuminates between the B+ circuit terminal 32 and ground.
- If all circuits test normal, replace the FPCM.
| ⇒ | If not within the specified range, refer to Charging System Test. |
| ⇒ | If greater than the specified range, test the ground circuit for an open/high resistance. |
| ⇒ | If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for FPCM replacement, setup, and programming.
