Battery Positive Cable Replacement LHD

1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection .



2. Disconnect the battery positive cable from the battery.



3. Depress the tabs in order to remove the underhood fuse block cover from the underhood fuse block.



4. Remove the nut (1) securing the battery positive cable (2) to the underhood fuse block.
5. Remove the starter heat shield. Refer to Starter Shield Replacement .



6. Reposition the protective boot from the generator output BAT terminal for access.
7. Remove the generator output BAT terminal nut (1) and disconnect the battery positive lead (2) from the generator.



8. Remove the starter terminal nut (2) and disconnect the battery positive cable (1) from the starter.
9. Lower the vehicle.



10. Disconnect the cable harness clip (2) from the lift bracket.
11. Remove the battery positive cable (1) from the engine.

1. Position the battery positive cable (1) to the engine.
2. Connect the cable harness clip (2) to the lift bracket.
3. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

Notice: Refer to Fastener Notice in the Preface section.




4. Connect the battery positive cable (1) to the starter and install the starter terminal nut (2).

Tighten
Tighten the battery positive cable to starter terminal nut to 12.5 N·m (111 lb in).




5. Connect the battery positive lead (2) to the generator and install the generator output BAT terminal nut (1).

Tighten
Tighten the generator output BAT terminal nut to 12.5 N·m (111 lb in).

6. Press the protective boot on to the generator output BAT terminal.
7. Install the starter heat shield. Refer to Starter Shield Replacement .
8. Lower the vehicle.



9. Install the nut (1) securing the battery positive cable (2) to the underhood fuse block.

Tighten
Tighten the battery positive cable to underhood fuse block nut to 15 N·m (11 lb ft).




10. Install the underhood fuse block cover to the underhood fuse block.



11. Connect the battery positive cable to the battery.

Tighten
Tighten the battery cable to 17 N·m (13 lb ft).

12. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection .

Battery Positive Cable Replacement RHD

1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection .



2. Disconnect the battery positive cable from the battery.



3. Remove the surge tank inlet hose from the retaining feature of the underhood fuse block cover.



4. Depress the tabs in order to remove the underhood fuse block cover from the underhood fuse block.



5. Remove the nut (1) securing the battery positive cable (2) to the underhood fuse block.
6. Remove the starter heat shield. Refer to Starter Shield Replacement .



7. Reposition the protective boot from the generator output BAT terminal for access.
8. Remove the generator output BAT terminal nut (1) and disconnect the battery positive lead (2) from the generator.



9. Remove the starter terminal nut (2) and disconnect the battery positive cable (1) from the starter.
10. Lower the vehicle.



11. Disconnect the cable harness clip (2) from the lift bracket.



12. Disconnect the cable harness clips (2) from the rear bracket and vent housing.
13. Remove the battery positive cable (1) from the engine.

1. Position the battery positive cable (1) to the engine.

Connect the cable harness clips (2) to the rear bracket and vent housing.




2. Connect the cable harness clip (2) to the lift bracket.
3. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

Notice: Refer to Fastener Notice in the Preface section.




4. Connect the battery positive cable (1) to the starter and install the starter terminal nut (2).

Tighten
Tighten the battery positive cable to starter terminal nut to 12.5 N·m (111 lb in).




5. Connect the battery positive lead (2) to the generator and install the generator output BAT terminal nut (1).

Tighten
Tighten the generator output BAT terminal nut to 12.5 N·m (111 lb in).

6. Press the protective boot on to the generator output BAT terminal.
7. Install the starter heat shield. Refer to Starter Shield Replacement .
8. Lower the vehicle.



9. Install the nut (1) securing the battery positive cable (2) to the underhood fuse block.

Tighten
Tighten the battery positive cable to underhood fuse block nut to 15 N·m (11 lb ft).




10. Install the underhood fuse block cover to the underhood fuse block.



11. Position the surge tank inlet hose to the retaining feature of the underhood fuse block cover.



12. Connect the battery positive cable to the battery.

Tighten
Tighten the battery cable to 17 N·m (13 lb ft).

13. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection .