GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2006 🢒 DTS 🢒 Vehicle Control Systems 🢒 Vehicle DTC Information 🢒 DTC B0014

DTC Descriptors

DTC B0014 01: Left Front Side Deployment Loop Short to Battery

DTC B0014 02: Left Front Side Deployment Loop Short to Ground

DTC B0014 04: Left Front Side Deployment Loop Open Circuit

DTC B0014 0D: Left Front Side Deployment Loop Resistance Above Threshold

DTC B0014 0E: Left Front Side Deployment Loop Resistance Below Threshold

Diagnostic Fault Information

Important: Always perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

Circuit

Short to Ground

High Resistance

Open

Short to Voltage

Signal Performance

Side Impact Module - LF High Circuit

B0014 02

B0014 0D

B0014 04

B0014 01

B0014 0E

Side Impact Module - LF Low Circuit

B0014 02

B0014 0D

B0014 04

B0014 01

B0014 0E

Circuit/System Description

During a side or frontal crash of sufficient force, the inflatable restraint sensing and diagnostic module (SDM) will allow current to flow through the deployment loop in order to deploy the side impact module - LF. The SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage.

A shorting bar used within the side impact module - LF connector which will short together both side impact module - LF high and low circuits when the connector is disconnected. This will help to prevent unwanted deployment of the inflator module during servicing.

Conditions for Running the DTC

Ignition voltage is between 9-16 volts.

Conditions for Setting the DTC

B0014 01

The side impact module - LF high and/or low circuit is short to voltage for 120 milliseconds.

B0014 02

The side impact module - LF high and/or low circuit is short to ground for 120 milliseconds.

B0014 04

The side impact module - LF high and/or low circuit is open for 120 milliseconds.

B0014 0D

The side impact module - LF deployment loop resistance is more than 3.9 ohms for 120 milliseconds.

B0014 0E

The side impact module - LF deployment loop resistance is less than 1.1 ohms for 120 milliseconds.

Action Taken When the DTC Sets
    • The SDM commands the AIR BAG indicator ON via serial data communications.
    • The SIR system is disabled and no deployments are allowed.

Conditions for Clearing the DTC
    • The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used.
    • A history DTC will clear once 255 malfunction-free ignition cycles have occurred.

Reference Information

Schematic Reference

SIR Schematics

Connector End View Reference

SIR Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Special Tools Required

    • J 38715-A SIR Driver/Passenger Load Tool
    • EL 38715-150 SIR Load Tool Adapter
    • J 38715-30A SIR Load Tool Adapter

Circuit/System Testing

    Important: When removing connectors, inspect for damage or corrosion. Damage or corrosion in the following requires repair or replacement of the affected component/connector:

       • The side impact module - LF
       • The side impact module wiring harness
       • The SDM module
       • The side impact module - LF wiring harness connector
       • The side impact module wiring harness connector
       • The SDM wiring harness connector

  1. Ignition OFF, disconnect the side impact module - LF wiring harness connector located under the driver front seat.
  2. Use EL 38715-150 adapter to connect the J 38715-A to the harness side of the side impact module - LF wiring harness connector. Use the PASSENGER INFLATOR connector located on the load tool.
  3. Ignition ON, use a scan tool to observe the SIR DTC display. Verify DTC B0014 is set history.
    4. ⇒If DTC B0014 is current, turn OFF the ignition and remove the SDM connector. Refer to SDM replacement in Repair Instructions for connector location.
    ⇒Test and repair both side impact module - LF high and low circuits for a short to voltage, short to ground, or open/low resistance. If all circuits test normal, replace the SDM.
  4. Ignition OFF, disconnect and remove the J 38715-A and adapter. Then connect the side impact module - LF wiring harness connector. Remove the side impact module - LF connector. Use J 38715-30A adapter to connect the J 38715-A to the harness side of the side impact module - LF connector. Use the PASSENGER INFLATOR connector located on the load tool.
  5. Ignition ON, use a scan tool to observe the SIR DTC display. Verify DTC B0014 is set history.
    6. ⇒If DTC B0014 is current, replace the side impact module - LF wiring harness.
  6. If DTC B0014 is history, replace the side impact module - LF.

Repair Instructions

Important: Always perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Driver and Passenger Seat Side Inflatable Restraint Module Replacement
    •  Inflatable Restraint Side Impact Module Wiring Harness Replacement
    •  Control Module References for SDM replacement, setup, and programming