GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC B2435 02: Left Seat Back Heater Sensor Circuit Short to Ground

DTC B2435 05: Left Seat Back Heater Sensor Circuit Short to Battery or Open

DTC B2440 02: Right Seat Back Heater Sensor Circuit Short to Ground

DTC B2440 05: Right Seat Back Heater Sensor Circuit Short to Battery or Open

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Left rear heated seat back element supply voltage

B2508 02

B1935 0C, B1935 0D

B2345 00, B2508 01

B1935 0B, B1935 0E

Left rear heated seat back element control

B2345 00, B2508 02

B1935 0C, B1935 0D

B2345 00, B2508 01

B1935 0B, B1935 0E

Left rear heated seat back temperature sensor signal

B2435 02

B1935 04, B1935 1F, B2435 0D

B1935 04, B1935 1F, B2435 0D

B1935 0A, B2345 13, B2345 42, B2345 4B

Left rear heated seat back temperature sensor low reference

--

B1935 04, B1935 1F, B2435 0D

--

B2345 13, B2345 42, B2345 4B

Left rear heated seat cushion element supply voltage

B2508 02

B2425 0C, B2425 0D

B2345 00, B2508 01

B2425 0B, B2425 0E

Left rear heated seat cushion element control

B2345 00, B2508 02

B2425 0C, B2425 0D

B2345 00, B2508 01

B2425 0B, B2425 0E

Left rear heated seat cushion temperature sensor signal

B1925 02, B2425 1F

B1925 05, B2425 04, B2425 1F

B1925 05, B2425 04, B2425 1F

B2345 13, B2345 42, B2345 4B, B2425 0A

Left rear heated seat cushion temperature sensor low reference

--

B1925 05, B2425 04, B2425 1F

--

B2345 13, B2345 42, B2345 4B

Right rear heated seat back element supply voltage

B2508 02

B2180 0C, B2180 0D

B2345 00, B2508 01

B2180 0B, B2180 0E

Right rear heated seat back element control

B2345 00, B2508 02

B2180 0C, B2180 0D

B2345 00, B2508 01

B2180 0B, B2180 0E

Right rear heated seat back temperature sensor signal

B2440 02

B2180 04, B2180 1F, B2440 05

B2180 04, B2180 1F, B2440 05

B2180 0A, B2345 13, B2345 42, B2345 4B

Right rear heated seat back temperature sensor low reference

--

B2180 04, B2180 1F, B2440 05

--

B2345 13, B2345 42, B2345 4B

Right rear heated seat cushion element supply voltage

B2508 02

B2430 0C, B2430 0D

B2345 00, B2508 01

B2430 0B, B2430 0E

Right rear heated seat cushion element control

B2345 00, B2508 02

B2430 0C, B2430 0D

B2345 00, B2508 01

B2430 0B, B2430 0E

Right rear heated seat cushion temperature sensor signal

B2170 02, B2430 1F

B2430 04, B2430 1F, B2170 05

B2430 04, B2430 1F, B2170 05

B2345 13, B2345 42, B2345 4B, B2430 0A

Right rear heated seat cushion temperature sensor low reference

--

B2430 04, B2430 1F, B2170 05

--

B2345 13, B2345 42, B2345 4B

Circuit/System Description

The heated seat temperature sensor that set this diagnostic trouble code (DTC) is located in the seat back just under the seat cover with the seat heating element. The rear heated seat module (RHSM) supplies a separate 5-volt reference voltage through the temperature sensor signal circuit and a ground through the low reference circuit to the sensor. The module monitors the voltage of the sensor signal circuit to determine the temperature of the seat. The temperature sensor varies in resistance based on the temperature of the heating element, causing the signal voltage to change. Once the seat reaches the set temperature, the module will then cycle the control circuit of the heating elements ON and OFF in order to maintain the desired seat temperature based on the feedback voltage from the sensors.

Conditions for Running the DTC

The heated seat system must be active.

Conditions for Setting the DTC

The temperature sensor voltage drops below 0.80 volt for more than 1 second.

Action Taken When the DTC Sets

The heated seat function for the affected seat will be disabled.

Conditions for Clearing the DTC

    • The current DTC will clear and set to history 3 seconds after the reference voltage returns to the normal operating range and the power mode changes to OFF then back to ACC or RUN.
    • The history DTC will clear after 50 consecutive fault-free ignition cycles have occurred.

Reference Information

Schematic Reference

Rear Seat Schematics

Connector End View Reference

Power Seat Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

    •  Scan Tool Data List
    •  Scan Tool Data Definitions

Circuit/System Testing

B2435 02 or B2435 05

  1. Ignition OFF, disconnect the C2, C4 harness connectors at the RHSM.
  2. Test for 1.4K-300K ohms between the signal circuit terminal 19 C4 and the low reference circuit terminal 5 C2.
  3. If greater than the specified range, test the signal circuit and low reference circuit for a short to voltage or an open/high resistance. If the circuits test normal, replace the seat back temperature sensor.
    If less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat back temperature sensor.
  4. Ignition OFF, connect the C2, C4 harness connectors to the RHSM.
  5. Disconnect the harness connector at the seat back heating element/temperature sensor.
  6. Ignition ON, test for 4.8-5.2 volts between the signal circuit terminal C and ground.
  7. If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the RHSM.
    If less than the specified range, test the signal circuit for a short to ground. If the circuit tests normal, replace the RHSM.
  8. If all circuits test normal, replace the RHSM.

B2440 02 or B2440 05

  1. Ignition OFF, disconnect the C2, C4 harness connectors at the RHSM.
  2. Test for 1.4K-300K ohms between the signal circuit terminal 10 C4 and the low reference circuit terminal 7 C2.
  3. If greater than the specified range, test the signal circuit and low reference circuit for a short to voltage or an open/high resistance. If the circuits test normal, replace the seat back temperature sensor.
    If less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat back temperature sensor.
  4. Ignition OFF, connect the C2, C4 harness connectors to the RHSM.
  5. Disconnect the harness connector at the seat back heating element/temperature sensor.
  6. Ignition ON, test for 4.8-5.2 volts between the signal circuit terminal C and ground.
  7. If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the RHSM.
    If less than the specified range, test the signal circuit for a short to ground. If the circuit tests normal, replace the RHSM.
  8. If all circuits test normal, replace the RHSM.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Rear Seat Back Cushion Heater Replacement
    •  Control Module References for RHSM replacement, programming and setup