Diagnostic Instructions
DTC Descriptors
DTC C0712 01: Level Control Compressor Circuit shorted to voltage
DTC C0712 06: Level Control Compressor Circuit shorted to ground or open
Circuit/System Description
The automatic level control (ALC) adjusts the vehicle suspension ride height. The electronic suspension control (ESC) module determines the height of the vehicle based on the voltage from the ALC sensor. The ESC module grounds the ELC COMP relay and the
exhaust control solenoid to raise and lower the vehicle in order to keep the vehicle level.
Conditions for Running the DTC
• | The ESC module is powered up. |
• | The ESC module is commanding the compressor ON. |
Conditions for Setting the DTC
The compressor relay output is shorted to voltage, ground, or open for 10 seconds.
Action Taken When the DTC Sets
The ALC will be inoperative.
Conditions for Clearing the DTC
The ESC module does not detect a failure during the self test.
Diagnostic Aids
This circuit is monitored during every functional operation of the compressor relay output and every 3.3 milliseconds when output is active. If a compressor relay fault is detected, the ESC module retries the output every 15 seconds to try
to recover from the fault.
Reference Information
Schematic Reference
Automatic Level Control Schematics
Connector End View Reference
Automatic Level Control Connector End Views
Description and Operation
Automatic Level Control Description and Operation
Electrical Information Reference
Scan Tool Reference
Circuit/System Verification
Ignition ON, command the compressor relay ON with a scan tool. Listen for the operation of the ELC CMPRSR relay and the ALC compressor.
Circuit/System Testing
- Ignition OFF, disconnect the ELC CMPRSR relay.
- Ignition ON, verify that a test lamp does not illuminate between the control circuit terminal 11 and ground.
⇒ | If the test lamp illuminates, test the control circuit for a short to voltage. |
- Verify that a test lamp illuminates between the B+ circuit terminal 15 and ground.
⇒ | If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit tests normal and the ELC CMPRSR fuse is open, test the control circuit terminal 12 for a short to ground. If the
circuit tests normal, test or replace the ELC CMPRSR relay. |
- Connect a test lamp between the B+ circuit terminal 15 and the control circuit terminal 11.
- Command the ELC CMPRSR relay ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
⇒ | If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the ESC module. |
⇒ | If the test lamp is always OFF, test the control circuit for a short to voltage
or an open/high resistance. If the circuit tests normal, replace the ESC module. |
- If all circuits test normal, test or replace the ELC CMPRSR relay.
Component Testing
Relay Test
- Ignition OFF, disconnect the ELC CMPRSR relay.
- Test for 40-200 ohms of resistance between terminals 85 and 86.
⇒ | If the resistance is not within the specified range, replace the relay. |
- Test for infinite resistance between the following terminals:
⇒ | If not the specified value, replace the relay. |
- Test for less than 2 ohms of resistance between terminals 30 and 87A.
⇒ | If greater than the specified range, replace the relay. |
- Install a 3-amp fused jumper wire between relay terminal 85 and 12 volts. Install a jumper wire between relay terminal 86 and ground. Test for less than 2 ohms of resistance between terminals 30 and 87.
⇒ | If greater than the specified range, replace the relay. |
Repair Instructions
Repair Verification
- Install any components or connectors that have been removed or replaced during diagnosis.
- Perform any adjustment, programming or setup procedures that are required when a component or module is removed or replaced.
- Clear the DTCs.
- Use the scan tool Diagnostic Counter Reset output control function to bypass the 3 consecutive ignition cycle requirement for setting a DTC. This will ensure that if a DTC was to be reset during the repair verification process, it will be displayed
on the scan tool.
- Turn OFF the ignition for 60 seconds.
- Turn ON the ignition.
- If the repair was related to a DTC, duplicate the Conditions for Running the DTC and use the Freeze Frame/Failure Records, if applicable, in order to verify the DTC does not reset. If the DTC resets or another DTC is present, refer to the
Diagnostic Trouble Code (DTC) List - Vehicle and perform the appropriate diagnostic procedure.