DTC Descriptors
| • | DTC B1735 01 Driver Seat Front Up Switch Circuit |
| • | DTC B1740 01 Driver Seat Front Down Switch Circuit |
| • | DTC B1745 01 Driver Seat Rear Up Switch Circuit |
| • | DTC B1750 01 Driver Seat Rear Down Switch Circuit |
| • | DTC B1755 01 Driver Seat Assembly Horizontal Forward Switch Circuit |
| • | DTC B1760 01 Driver Seat Assembly Horizontal Rearward Switch Circuit |
| • | DTC B1815 01 Driver Seat Recline Forward Switch Circuit |
| • | DTC B1820 01 Driver Seat Recline Rearward Switch Circuit |
| • | DTC B1830 01 Driver Seat Lumbar Forward Switch Circuit |
| • | DTC B1835 01 Driver Seat Lumbar Rearward Switch Circuit |
| • | DTC B1840 01 Driver Seat Lumbar Up Switch Circuit |
| • | DTC B1845 01 Driver Seat Lumbar Down Switch Circuit |
Diagnostic Fault Information
Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Front Vertical Up Switch Signal | 3 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01, | -- |
Front Vertical Down Switch Signal | 3 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01, | -- |
Rear Vertical Up Switch Signal | 3 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01, | -- |
Rear Vertical Down Switch Signal | 3 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01, | -- |
Horizontal Forward Switch Signal | 3 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01, | -- |
Horizontal Rearward Switch Signal | 3 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01, | -- |
Recline Forward Switch Signal | 3 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01, | -- |
Recline Rearward Switch Signal | 3 | 1 | B1735 01, B1740 01, B1745 01, B1750 01, B1755 01, B1760 01, B1815 01, B1820 01, | -- |
Driver Seat Lumbar Up Switch Signal | 3 | 2 | 2 | -- |
Driver Seat Lumbar Down Switch Signal | 3 | 2 | 2 | -- |
Driver Seat Lumbar Forward Switch Signal | 3 | 2 | 2 | -- |
Driver Seat Lumbar Rearward Switch Signal | 3 | 2 | 2 | -- |
Passenger Seat Lumbar Up Switch Signal | 3 | 2 | 2 | -- |
Passenger Seat Lumbar Down Switch Signal | 3 | 2 | 2 | -- |
1. Power Seat Inoperative with Memory-A45 2. Lumbar Support Inoperative with Memory-A45 3. Scan Tool Does Not Communicate with Low Speed GMLAN Device | ||||
Circuit Description
When the power seat switches are pressed, they send a 12-volt signal through the switch signal circuits to the memory seat module (MSM). The MSM then commands the driver seat and lumbar motors to move in response to the switch signals.
Conditions for Running the DTC
The MSM must be powered.
Conditions for Setting the DTC
| • | If a seat switch circuit is active in one direction and the switch for the opposite direction is pressed, this DTC will set. |
| • | A short to voltage on a switch signal circuit. |
Action Taken When the DTC Sets
| • | A motor output driven in response to a switch considered failed, is deactivated for both directions. |
| • | All memory recall commands are ignored. |
| • | The MSM will respond to any other switch signal that has not set a DTC. |
Conditions for Clearing the DTC
| • | The current DTC will clear and set the code to history, 3 seconds after the fault is no longer present and the power mode changes to OFF then back to ACC or RUN. |
| • | The history DTC will clear after 50 consecutive fault-free ignition cycles have occurred. |
Diagnostic Aids
| • | The scan tool may reference the Memory Seat Module (MSM) as the Driver Position Module. |
| • | If one of the switch signal circuits is shorted to battery, multiple codes will set. |
Reference Information
Schematic Reference
Connector End View Reference
Power Seat Connector End Views
Electrical Information Reference
Scan Tool Reference
Circuit/System Verification
Ignition ON, observe the scan tool Driver Position Module, Seat 1 Inputs seat switch parameters, while pressing the seat directional switches. The reading should change between Inactive and Active.
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at the appropriate seat or lumbar adjuster switch.
- Ignition ON, verify the scan tool seat or lumbar switch parameters are Inactive.
- If all circuits test normal, test or replace the appropriate seat or lumbar adjuster switch.
| ⇒ | If not Inactive, test the signal circuit that displays Active for a short to voltage. If the circuit tests normal, replace the MSM. |
Component Testing
- Ignition OFF, disconnect the harness connector at the appropriate seat or lumbar adjuster switch.
- Test for infinite resistance between each seat direction signal terminal and the switch B+ terminal with the switch in the open position.
- Test for less than 1 ohm of resistance between each seat direction signal terminal and the B+ terminal with the switch in the closed position.
| ⇒ | If less than infinite resistance, replace the switch. |
| ⇒ | If greater than 1 ohm, replace the switch. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for memory seat module replacement, setup, and programming |
