GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2007 🢒 DTS 🢒 Engine 🢒 Engine Controls and Fuel - 4.6L 🢒 DTC P0016

Diagnostic Instructions
    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provide an overview of each diagnostic category.

DTC Descriptor

DTC P0016: Crankshaft Position (CKP) - Intake Camshaft Position (CMP) Correlation

Circuit/System Description

The engine control module (ECM) uses the crankshaft position (CKP) sensor and the intake camshaft position (CMP) sensor information to monitor the correlation between the crankshaft and intake camshaft position.

Conditions for Running the DTC
    • DTCs P0335, P0336, P0340, and P0341 are not set.
    • The engine is running.
    • DTC P0016 runs continuously when the above conditions are met.

Conditions for Setting the DTC

The ECM detects the cam sensor pulses occur during the incorrect crankshaft position for 25 out of 35 engine cycles.

Action Taken When the DTC Sets
    • The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC
    • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Diagnostic Aids

Inspect the engine for any recent engine mechanical repairs. An incorrectly installed camshaft, crankshaft, or timing chain can cause this DTC to set.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

    •  Engine Controls Connector End Views
    •  Engine Control Module Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

    •  Scan Tool Data List
    •  Scan Tool Data Definitions

Circuit/System Verification
  1. Observe the DTC Information with a scan tool.
    2. ⇒If the scan tool displays that any other DTCs also failed this ignition, refer to Diagnostic Trouble Code (DTC) List - Vehicle .

    Important: If you cannot duplicate the condition, operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

    ⇒If only DTC P0016 is displayed, continue with Circuit/System Testing.
  2. Engine running, observe the DTC information with a scan tool. DTC P0016 should not set.
  3. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame Records data.

Circuit/System Testing

Inspect for an incorrectly installed timing chain, excessive play in the timing chain, or for a timing chain that jumped teeth. Refer to Camshaft Timing Drive Chain Alignment Diagram and Camshaft Timing Drive Components Cleaning and Inspection .

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.