GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2007 🢒 DTS 🢒 Engine 🢒 Engine Controls and Fuel - 4.6L 🢒 DTC P0153, P0154, P1153, or P2A03

Diagnostic Instructions
    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provide an overview of each diagnostic category.

DTC Descriptors

DTC P0153: HO2S Slow Response Bank 2 Sensor 1

DTC P0154: HO2S Circuit Insufficient Activity Bank 2 Sensor 1

DTC P1153: HO2S Insufficient Switching Bank 2 Sensor 1

DTC P2A03: HO2S Performance Bank 2 Sensor 1

Diagnostic Fault Information

Circuit

Short to Ground

High Resistance

Open

Short to Voltage

Signal Performance

HO2S High Signal

P0131, P0132, P0134, P0137, P0140, P0151, P0154, P1133, P1153, P2A00, P2A01, P2A03

P0131, P0133, P0134, P0137, P0140, P0151, P0153, P0154, P1133, P1153, P2A00, P2A01, P2A03

P0131, P0133, P0134, P0137, P0140, P0153, P0154, P1133, P1153, P2A00, P2A01, P2A03

P0132, P0134, P0138, P0140, P0152, P0154, P1133, P1153, P2A00, P2A01, P2A03

P0133, P0134, P0140, P0153, P1133, P1153, P2A00, P2A01, P2A03

HO2S Low Signal

P2A00, P2A01, P2A03

P0131, P0133, P0134, P0138, P0140, P0151, P0153, P0154, P1133, P1153, P2A00, P2A01

P0131, P0133, P0134, P0138, P0140, P0153, P0154, P1133, P1153, P2A00, P2A01, P2A03

P0134, P0138, P0140, P0152, P0153, P1133, P1153, P2A00, P2A01, P2A03

P2A00, P2A01, P2A03

Typical Scan Tool Data

HO2S Sensor 1 Voltage

Circuit

Short to Ground

Open

Short to Voltage

Normal Range: 200-800 mV

HO2S High Signal

0 mV

Approximately 470 mV

Approximately 1,100 mV

HO2S Low Signal

455 mV

Approximately 450 mV

Approximately 445 mV

Circuit/System Description

Heated oxygen sensors (HO2S) are used for fuel control and post catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content in the exhaust stream. The HO2S must reach operating temperature to provide an accurate voltage signal. Heating elements inside the HO2S minimize the time required for the sensors to reach operating temperature. The control module supplies the HO2S with a reference, or bias, voltage of about 450 mV. When the engine is first started, the control module operates in Open Loop, ignoring the HO2S voltage signal. Once the HO2S reaches operating temperature and Closed Loop is achieved, the HO2S generates a voltage within a range of 0-1,000 mV that fluctuates above and below bias voltage. High HO2S voltage indicates a rich exhaust stream. Low HO2S voltage indicates a lean exhaust stream.

Conditions for Running the DTC

P0153

    • DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
    • The Engine Coolant Temperature (ECT) Sensor parameter is more than 70°C (158°F).
    • The Ignition 1 Signal parameter is between 10-18 volts.
    • The Fuel Level Sensor parameter is more than 10 percent.
    • The Engine Run Time parameter is more than 202 seconds.
    • The Engine Speed parameter is between 1,100-2,500 RPM.
    • The BARO Sensor parameter is more than 70 kPa.
    • The Mass Airflow (MAF) Sensor parameter is between 20-40 g/s.
    • The Loop Status parameter is Closed.
    • The Throttle Position (TP) Indicated Angle parameter is more than 3 percent.
    • These DTCs run once per drive cycle when the above conditions are met for 1 second.

P0154

    • DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
    • The Ignition 1 Signal parameter is between 10-18 volts.
    • The engine run time is more than 101 seconds.
    • These DTCs run continuously when the above conditions are met.

P1153

    • DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516, P2101, P2119, P2135, P2176 are not set.
    • The ECT Sensor parameter is more than 70°C (158°F).
    • The Engine Speed parameter is between 1,100-2,500 RPM.
    • The Ignition 1 Signal parameter is between 10-18 volts.
    • The Engine Run Time parameter is more than 202 seconds.
    • The Loop Status parameter is Closed.
    • The TP Indicated Angle parameter is more than 5 percent.
    • The Fuel Level Sensor parameter is more than 10  percent.
    • The BARO parameter is more than 70 kPa.
    • The MAF Sensor parameter is between 20-40 g/s.
    • These DTCs run once per drive cycle when the above conditions are met for 1 second.

P2A03

    • DTCs P0030, P0036, P0053, P0054, P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0125, P0128, P0131, P0132, P0133, P0134, P0135, P0137, P0138, P0140, P0141, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1516, P2101, P2119, P2135, P2176, 2A00 are not set.
    • The Engine Run Time parameter is more than 100 seconds.
    • The ignition 1 Signal parameter is between 10-18 volts.
    • The MAF sensor parameter is between 3-30 g/s.
    • The Engine Speed parameter is between 500-5,000 RPM.
    • DTC P2A03 runs continuously when the above conditions are met for 5 seconds.

Conditions for Setting the DTC

P0153

    • The control module detects that the HO2S 1 rich-to-lean or lean-to-rich average response time is more than 0.14 second.
    • These DTCs set within 60 seconds when the above condition is met.

P0154

    • The control module detects that the HO2S 1 parameter is between 400-500 mV.
    • The Throttle Position (TP) Indicated Angle parameter changes more than 5 percent.
    • These DTCs set within 101 seconds when the above conditions are met.

P1153

    • The control module detects that the HO2S 1 rich-to-lean counts, or the lean-to-rich counts are less than a calibrated value.
    • These DTCs set within 60 seconds when the above condition is met.

P2A03

    • The control module detects that the Loop Status parameter is open.
    • DTCs P2A00 and P2A03 set within 5 seconds when the above condition is met.

Action Taken When the DTC Sets

DTCs P0153, P0154, P1153, P2A03 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P0153, P0154, P1153, P2A03 are Type B DTCs.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

    •  Engine Control Module Connector End Views
    •  Engine Controls Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs
    •  Heated Oxygen Sensor Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Scan Tool Data List

Circuit/System Verification
  1. If any HO2S heater DTCs are set, perform those diagnostics first.
  2. Allow the engine to reach operating temperature.
  3. Engine running, observe the affected HO2S parameter with a scan tool.
    4. • The pre-catalyst oxygen sensors value should vary from below 200 mV to above 800 mV and respond to fueling changes.
    • The post-catalyst oxygen sensors value should change more than 200 mV when the throttle is quickly cycled 3 times from closed to wide open and back to closed after running the engine at 1,500 RPM for 30 seconds.
  4. The affected HO2S may be damaged due to contamination. Prior to replacing the affected HO2S, inspect for the following sources of contamination:

    5. Notice: Refer to Silicon Contamination of Heated Oxygen Sensors Notice in the Preface section.

    • A silicon contaminated HO2S
    • Fuel contamination--Refer to Alcohol/Contaminants-in-Fuel Diagnosis .
    • Engine oil consumption--Refer to Oil Consumption Diagnosis .
    • Engine coolant consumption--Refer to Loss of Coolant .
  5. Engine running, observe the DTC information with a scan tool. DTCs P0153, P0154, P1153 or P2A03 should not set.
  6. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

    Important: All modules must be powered down or misdiagnosis may result.

  1. Ignition OFF, disconnect the scan tool and wait 60 seconds to ensure all modules are powered down.
  2. Ignition OFF, disconnect the harness connector at the appropriate HO2S.
  3. Ignition OFF, measure for less than 5 ohms resistance between the appropriate HO2S low signal circuit terminal A and ground.
    4. ⇒If more than the specified range, test the appropriate HO2S low signal circuit for an open/high resistance. If the circuit tests normal, replace the ECM.
  4. Ignition ON, verify the appropriate scan tool HO2S parameter is approximately 450 mV.
    5. ⇒If more than the specified value, test the appropriate HO2S high signal circuit for a short to voltage. If the circuit tests normal, replace the ECM.
    ⇒If less than the specified value, test the appropriate HO2S high signal circuit for a short to ground. If the circuit tests normal, replace the ECM.
  5. Ignition ON, install a 3A fused jumper wire at the HO2S high signal circuit terminal B. Toggle the jumper wire between the HO2S low signal circuit terminal A and battery voltage. Verify the appropriate scan tool HO2S parameter toggles between 0 mV and approximately 1,000 mV.
    6. ⇒If the appropriate scan tool HO2S parameter does not toggle correctly, test the HO2S high signal circuit for an open/high resistance. If the circuits test normal, replace the ECM.
  6. If all circuits test normal, replace the appropriate HO2S.

Repair Instructions

Notice: Refer to Heated Oxygen Sensor Resistance Learn Reset Notice in the Preface section.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Heated Oxygen Sensor Replacement - Bank 1 Sensor 1
    •  Heated Oxygen Sensor Replacement - Bank 1 Sensor 2
    •  Heated Oxygen Sensor Replacement - Bank 2 Sensor 1
    •  Control Module References for ECM replacement, setup, and programming