Circuit Description
The automatic transmission fluid temperature (TFT) sensor is a negative coefficient thermistor whose resistance value changes based on temperature. The transmission control module (TCM) provides a 5-volt reference to the sensor. A low fluid temperature or open circuit result in high signal voltage. The TFT operating range is -40 to +150°C (-40 to +302°F).
If the TCM detects a continuous open or a short to voltage on the TFT sensor circuit, then DTC P0713 sets. DTC P0713 is a type C DTC.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0713 Transmission Fluid Temperature (TFT) Sensor Circuit High Voltage
Conditions for Running the DTC
| • | No AT ISS DTCs P0716 or P0717. |
| • | No OSS DTCs P0722 or P0723. |
| • | The engine run time is greater than 5 seconds. |
| • | LD8: The transmission output shaft speed is 200 RPM or greater for 200 seconds cumulatively. |
| • | L37: The transmission output shaft speed is 239 RPM or greater for 200 seconds cumulatively. |
| • | The TCC slip speed is 120 RPM or greater for 200 seconds cumulatively. |
Conditions for Setting the DTC
The TCM detects a reading of less than -40°C (-40°F) for 80 seconds.
Action Taken When the DTC Sets
| • | The TCM does not request the engine control module (ECM) to illuminate the malfunction indicator lamp (MIL). |
| • | The TCM freezes transmission adaptive functions. |
| • | The TCM calculates a default transmission fluid temperature based on engine coolant temperature, intake air temperature and engine run time. |
| • | The TCM records the operating conditions when the Conditions for Setting the DTC are met. The TCM stores this information as Failure Records. |
| • | The TCM stores DTC P0713 in TCM history. |
Conditions for Clearing the DTC
| • | The TCM clears the DIC message when the condition no longer exists. |
| • | A scan tool can clear the DIC/DTC. |
| • | The TCM clears the DTC from TCM history if the vehicle completes 40 warm-up cycles without a non-emission related diagnostic fault occurring. |
| • | The TCM cancels the DTC default actions when the fault no longer exists and the DTC passes. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests the TFT sensor signal circuit for being shorted to another circuit within the transmission. If the TFT sensor signal circuit shorts to another circuit, which is carrying voltage greater than five volts, the TFT sensor would become open.
-
This step tests the TFT sensor signal circuit for being shorted to voltage, which would be the cause for the open in the TFT sensor.
Step | Action | Values | Yes | No | ||||
|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |||||
2 |
Important: Before clearing the DTC, use the scan tool in order to record the DTC Failure Records. Using the Clear Info function erases the Failure Records from the TCM. Does the scan tool display a Trans. Fluid Temp. less than the specified value? | -39°C (-38°F) | Go to Step 3 | Go to Testing for Intermittent Conditions and Poor Connections | ||||
3 |
Refer to Automatic Transmission Inline 20-Way Connector End View . Does the resistance measure less than the specified value? | 100 K ohms | Go to Step 7 | Go to Step 4 | ||||
4 |
Refer to Testing for Continuity . Did you find an open condition? | -- | Go to Step 8 | Go to Step 5 | ||||
Measure the resistance between terminal L and all other terminals of the J 44152 . Does the resistance measure less than the specified value? | 1000 ohms | Go to Step 10 | Go to Step 6 | |||||
Test the signal circuit of the TFT sensor for a short to voltage between the TCM connector and the AT inline 20-way connector. Refer to Testing for a Short to Voltage and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 9 | Go to Step 9 | |||||
7 |
Refer to Testing for Continuity and Wiring Repairs . Did you find and correct an open condition? | -- | Go to Step 12 | Go to Step 11 | ||||
8 |
Important: The automatic transmission wiring harness consists of 2 separate harnesses, the Automatic Transmission Wiring Harness Assembly and the Automatic Transmission Wiring Extension Harness Assembly. In order to avoid the unnecessary replacement of parts, only replace the Automatic Transmission Wiring Harness Assembly. Replace the automatic transmission wiring harness. Refer to Input Speed Sensor and Wiring Harness Removal . Did you complete the replacement? | -- | Go to Step 12 | -- | ||||
9 | Replace the TFT sensor. Refer to Control Valve Upper Body Disassemble . Did you complete the replacement? | -- | Go to Step 12 | -- | ||||
10 |
Important: The automatic transmission wiring harness consists of 2 separate harnesses, the Automatic Transmission Wiring Harness Assembly and the Automatic Transmission Wiring Extension Harness Assembly. In order to avoid the unnecessary replacement of parts, only replace the Automatic Transmission Wiring Harness Assembly. Refer to Input Speed Sensor and Wiring Harness Removal . Did you complete the replacements? | -- | Go to Step 12 | -- | ||||
11 | Replace the TCM. Refer to Control Module References . Did you complete the replacement? | -- | Go to Step 12 | -- | ||||
12 | Perform the following procedure in order to verify the repair:
Has the test run and passed? | -- | Go to Step 13 | Go to Step 2 | ||||
13 | With the scan tool, observe the stored information, capture info. and DTC info. Does the scan tool display any DTCs that you have not diagnosed? | -- | System OK |
