Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC B320A 39: Front Door Window Motor Internal Electronic FailureDTC B320A 42: Front Door Window Motor Calibration Data Set Not Programmed
DTC B320A 4B: Front Door Window Motor Calibration Not Learned
DTC B320B 39: Rear Door Window Motor Internal Electronic Failure
DTC B320B 42: Rear Door Window Motor Calibration Data Set Not Programmed
DTC B320B 4B: Rear Door Window Motor Calibration Not Learned
DTC B320C 39: Middle Door Window Motor Internal Electronic Failure
DTC B320C 42: Middle Door Window Motor Calibration Data Set Not Programmed
DTC B320C 4B: Middle Door Window Motor Calibration Not Learned
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Driver Door Module B+ | U0199 00 | U0199 00 | -- | -- |
Driver Window Motor B+ | U1511 00 | U1511 00 | -- | B320A 4B |
LR Window Motor B+ | U1512 00 | U1512 00 | -- | -- |
Passenger Door Module B+ | U0200 00 | U0200 00 | -- | -- |
Front Passenger Window Motor B+ | U1511 00 | U1511 00 | -- | B320A 4B |
RR Window Motor B+ | U1512 00 | U1512 00 | -- | -- |
Driver Window Motor Serial Data | U1511 00 | U1511 00 | 1 | B320A 4B |
Front Passenger Window Motor Serial Data | U1500 02, U1511 00 | U1511 00 | 2 | B320A 4B |
LR Window Motor Serial Data | U1500 02, U1512 00 | U1512 00 | 3 | -- |
RR Window Motor Serial Data | U1500 02, U1512 00 | U1512 00 | 4 | -- |
LR Window Switch Voltage Reference | 3 | 3 | 3 | -- |
RR Window Switch Voltage Reference | 4 | 4 | 4 | -- |
Power Window Switch Left Rear Signal | 3 | 3 | 3 | -- |
Power Window Switch Right Rear Signal | 4 | 4 | 4 | -- |
Driver Door Module Ground | -- | U0199 00, U0200 00 | -- | -- |
Passenger Door Module Ground | -- | U0200 00 | -- | -- |
Driver Window Motor Ground | -- | U0199 00, U0200 00 | -- | -- |
Front Passenger Window Motor Ground | -- | U1511 00 | -- | B320A 4B |
LR Window Motor Ground | -- | U1512 00 | -- | B320A 42 |
RR Window Motor Ground | -- | U1512 00 | -- | B320A 42 |
1. Driver Window Malfunction 2. Passenger Window Malfunction 3. Left Rear Window Malfunction 4. Right Rear Window Malfunction | ||||
Circuit/System Description
The front door, rear door and middle door power window motors communicate with the driver door module (DDM), passenger door module (PDM) and rear door modules and middle door modules through a serial data message. The motors contain a logic module which must be normalized or programmed any time the window motor is serviced to provide proper operation and communication between door modules and window motors.
Conditions for Running the DTC
Power window switch activated.
Conditions for Setting the DTC
B320A 39, B320B 39, B320C 39
An internal malfunction or a momentary voltage spike has been detected by the DDM or PDM in the power window motor while commanding the window UP/DOWN.
B320A 42, B320B 42, B320C 42
A not normalized/programmed power window motor.
B320A 4B, B320B 4B, B320C 4B
The window motor experiences a loss of voltage in the B+ circuit or an open/high resistance in the serial data circuit.
Action Taken When the DTC Sets
The appropriate power window will malfunction
Conditions for Clearing the DTC
B320A 39, B320B 39, B320C 39
If the DTC is current, the appropriate window motor must be replaced before the DTC can be cleared.
B320A 42, B320B 42, B320C 42
The affected power window motor must be programmed before the DTC can be cleared.
B320A 4B, B320B 4B, B320C 4B
The affected power window motor must be calibrated before the DTC can be cleared.
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Power Windows Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
Ignition ON, observe the operation of each power window while commanding each window UP and DOWN by using the power window switches on the driver master control. Each power window should go UP and DOWN command.
Circuit/System Testing
B320A 39, B320B 39, B320C 39
Ignition ON, command the appropriate power window DOWN and UP with a scan tool. The power window should go DOWN and UP as commanded.
| ⇒ | If the DTC is current and the power window is inoperative, replace the power window motor. |
| ⇒ | If the DTC is history and the power window performs the UP and DOWN functions, clear the DTC. |
B320A 42, B320B 42 or B320C 42
Reprogram the appropriate power window and operate the power window within the conditions for running the DTC, verify the DTC does not reset.
| ⇒ | If the DTC resets, replace the power window motor. |
B320A 4B, B320B 4B or B320C 4B
Command the appropriate power window motor fully DOWN by pressing and holding the window switch for 5 seconds, then command the power window motor fully UP by lifting and holding the window switch for 5 seconds. Operate the power window within the conditions for running the DTC, verify the DTC does not reset
| ⇒ | If the DTC resets, replace the power window motor. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
