GM Service Manual Online
For 1990-2009 cars only

Removal Procedure

    Warning: Refer to Approved Equipment for Collision Repair Warning in the Preface section.

    Note: Before beginning the repair, refer to Metal Panel Bonding for proper adhesive applicator preparations and general information.

  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  2. Disable the SIR system. Refer to SIR Disabling and Enabling.
  3. Remove the door from the vehicle. Refer to Front Side Door Replacement.
  4. Remove the outer door handle. Refer to Front Side Door Outside Handle Replacement.
  5. Remove the outside rear view mirror. Refer to Power Mirror Replacement.
  6. Drill out the spot welds that attach the outer belt reinforcement to the outer door panel flange.

  7. Object Number: 864417  Size: SH
  8. Grind the edges of the door outer panel to separate the outer door panel from the door shell.

  9. Object Number: 864445  Size: SH
  10. Remove the outer door panel.
  11. Remove the sealers and anti-corrosion materials from the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair.

  12. Object Number: 864452  Size: SH
  13. Straighten the edges of the door shell.

Installation Procedure


    Object Number: 873321  Size: SH
  1. Grind the surface of the door shell mating flanges to bare steel.

  2. Object Number: 864458  Size: SH
  3. Scuff the opposing mating surfaces of the door outer panel to remove the gloss of the E-Coat.
  4. Prepare all mating surfaces as necessary.
  5. Apply 3M® Weld-Thru coating P/N 05916 or equivalent to all mating surfaces.

  6. Object Number: 805595  Size: SH

    Note: The adhesive has a 40-50 minute working time. Do not allow the door to totally cure off the vehicle, as proper alignment of the door outer panel to the door shell will be difficult.

  7. Apply a 3-6 mm (1/8 to 1/4 in) bead of metal panel bonding adhesive GM P/N 12378566/7 (Canadian P/N 88901674/5) or equivalent to both of the mating surfaces.
  8. Using a small acid brush, spread a coat of adhesive to cover all the bare metal surfaces to ensure corrosion protection.
  9. Apply a 9-13 mm (3/8 to 1/2 in) bead of metal panel bonding adhesive GM P/N 12378566/7 (Canadian P/N 88901674/5) or equivalent to the service part mating surfaces.

  10. Object Number: 864496  Size: SH

    Note: DO NOT pull the panels apart after being joined together. Slide the panels against each other to realign the panels.

  11. Install the door outer panel to the door shell.
  12. Clamp the door outer panel into position as required.

  13. Object Number: 864499  Size: SH
  14. Using a hammer re-hem the hem flanges around the door shell.
  15. Continue to hammer in stages along the hem flanges.

  16. Using lacquer thinner remove the excess adhesive from the door panel area.
  17. Install the door to the vehicle check the door outer panel for proper alignment, adjust the alignment as required. Refer to Front Side Door Replacement.
  18. Remove the door from the vehicle to complete the repair.

  19. Object Number: 864502  Size: SH
  20. Apply Fusor super flexible anti-flutter foam - fast set, Fusor P/N 121/124 or equivalent in 4-5 evenly spaced locations between the door outer panel and the inner safety beam.
  21. Apply sealers and anti-corrosion materials to the repair area as necessary. Refer to Anti-Corrosion Treatment and Repair.
  22. Paint the repaired area. Refer to Basecoat/Clearcoat Paint Systems.
  23. Install the door to the vehicle. Inspect the door outer panel for proper alignment and adjust the alignment as required. Refer to Front Side Door Replacement.
  24. Install the outer door handle. Refer to Front Side Door Outside Handle Replacement.
  25. Install the outside rear view mirror. Refer to Power Mirror Replacement.
  26. Enable the SIR system. Refer to SIR Disabling and Enabling.
  27. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.